NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
The Plaster Cast: Gypsum That Sets Round a Broken Limb
Charlie

Tạo bởi

Charlie

27. tháng Chín 2026DE
2
0
0
0
0

The Plaster Cast: Gypsum That Sets Round a Broken Limb

A broken bone heals only if its ends are held still in line for weeks. Splints of wood and bandages stiffened with starch or egg white took hours or days to harden. Antonius Mathijsen, a Dutch army surgeon at the military hospital in Haarlem, rubbed plaster of Paris into coarse cotton bandages in 1851: soaked in water and wrapped round the limb, they could be moulded to it and set hard within minutes. He published the method in February 1852, and armies adopted it because it could be applied on the battlefield. The chemistry is simple: the hemihydrate takes up water and crystallises as gypsum. But the reaction gives off heat, and the water the mix needs to be workable is far more than the reaction uses. This rung works out the heat and the water, models a setting cast's temperature, and makes a cast round a bottle, measuring its temperature as it sets.
Cơ bản
About 3 hours

Hướng dẫn

1

Hydration chemistry, water ratio and heat

Đang tải sổ tay Jupyter…
2

The older plaster it follows

Lime plaster sets by taking up carbon dioxide over days; gypsum plaster sets by taking up water in minutes. The embedded blueprint makes the older one.
3

Measure the heat of setting

Weigh 100 g of plaster of Paris into a paper cup and 60 g of water at room temperature into another. Stir the plaster into the water, push a thermocouple probe into the middle, and read the temperature every minute for 40 minutes. Repeat with a thin disc — 100 g spread 5 mm thick on a plastic sheet with the probe under it — and with a deep cup of 300 g. Plot the three curves: the thick lump gets far hotter than the thin disc, as the notebook's model shows. Never repeat the deep test with warm water near skin.

Vật liệu cho bước này:

Thạch cao ParisThạch cao Paris1 kilogram
CốcCốc3 cái
NướcNước1 lít

Công cụ cần thiết:

Cân nhà bếp điện tửCân nhà bếp điện tử
Cặp nhiệt điện có đồng hồ hiển thịCặp nhiệt điện có đồng hồ hiển thị
Đồng hồ bấm giờĐồng hồ bấm giờ
Găng tay da bảo hộGăng tay da bảo hộ
Kính bảo hộ trong suốtKính bảo hộ trong suốt
4

Wrap a cast round a bottle

Use a plastic bottle as the limb. Smear it with petroleum jelly so the cast releases, and wrap one layer of cotton gauze as padding. Cut plaster bandage into lengths. Dip each in cool water for a few seconds until the bubbles stop, squeeze it gently, and wrap it round with each turn overlapping the last by half, smoothing it with a wet palm so the layers bond. Build four to six layers, thicker where a real cast takes the load. Mould it with flat palms, never fingertips, which leave dents that press on skin. It is firm in minutes and sets fully over hours as it dries. Next day, cut it off with a saw down one side and weigh it wet and dry.

Vật liệu cho bước này:

Cuộn băng bột thạch cao làm mặt nạCuộn băng bột thạch cao làm mặt nạ1 cái
Gạc bôngGạc bông1 cái
VaselineVaseline1 cái
Chai PET (nước có ga)Chai PET (nước có ga)1 cái
NướcNước2 lít

Công cụ cần thiết:

XôXô
Găng tay da bảo hộGăng tay da bảo hộ
Cân nhà bếp điện tửCân nhà bếp điện tử
Cưa sắtCưa sắt
5

A cast that is not right

Warning signs with a plaster cast. On a real patient, any of them means seeing a clinician.

Flow

Loading...
6

History and honest limits

**Antonius Mathijsen** (1805–1878) first used plaster of Paris bandages in 1851 at the military hospital in Haarlem, and published the method in the Dutch journal *Repertorium* in February 1852; he took out no patent. Fibreglass and resin casts now often replace plaster because they are lighter and tolerate water, but plaster is still used where it must be moulded closely. **Honest limits.** The temperature model is a simple lumped estimate, not a clinical figure. Applying a cast to a person is a clinical skill: this rung casts a bottle. The enthalpy figures are standard tabulated values; real plasters differ slightly by type.

Vật liệu

7

Công cụ yêu cầu

7

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...