NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO

The Shears-Cup Lemon Squeezer: Two Cups on Crossed Handles, a Slotted Recess for the Juice
A lemon squeezer lets the seeds through with the juice, or crushes them into it, and its holes clog with pulp.
Thomas Reece and Arthur Clarke of Philadelphia, Pennsylvania, received US 61,251, dated 15 January 1867, for a squeezer of two cups of metal or wood on handles "pivoted together at x, so that the cups may be separated or brought together similar to the blades of a pair of shears." The larger cup has a small recess in its bottom with slots radiating from its centre, so formed "as not to allow any seed to pass through them", and the smaller cup has a flange that stops it going too far into the other.
This rung works out the squeeze through the crossed handles, with a work check, then makes the squeezer from two tins on flat-bar handles, and squeezes lemons with it.
Trung cấp
About 4 hours
Hướng dẫn
1
1
Crossed handles
Crossed handles
Đang tải sổ tay Jupyter…
2
2
A hinged squeezer before it
A hinged squeezer before it
The embedded blueprint pins its handles at their front ends. Reece and Clarke cross theirs like shears and slot the recess so seeds stay behind.
3
3
Read US 61,251
Read US 61,251
"The cup B is made smaller than cup A, and works within it with its bottom down. This cup B is provided around its mouth with a flange, d, which catches upon the mouth of cup A when the two cups are brought together, as shown in Figure 1. These cups are provided with the handles C and D, which said handles are pivoted together at x, so that the cups may be separated or brought together similar to the blades of a pair of shears."
"The space between the two cups allows the juice to be pressed out through the slots or openings without breaking the seed, and the slots are so formed and are of such a size as not to allow any seed to pass through them."
4
4
Make the squeezer and press lemons
Make the squeezer and press lemons
**Handles.** Cut two 25 cm lengths of 20 × 5 mm mild steel flat bar and drill each 8 cm from one end for an M6 pivot bolt, so they cross like shears.
**Cups.** Cut the bottoms from two clean tin cans, one about 8 cm across and one about 6.5 cm, each 3 cm deep. In the larger one's base, hammer a small recess over a hole in a hardwood block, and cut four narrow slots in it radiating from the centre, 2 mm wide. Rivet a ring of tinplate round the smaller one's mouth as the flange d.
**Assemble.** Rivet each cup to the short end of a handle so the smaller cup, bottom down, closes into the larger one when the handles are squeezed, and bolt the handles at the pivot.
**Test.** Halve a lemon, put one half cut side down in the larger cup over a glass, and squeeze. Count the seeds left in the cup and in the glass, and weigh the juice.
Vật liệu cho bước này:
Thanh thép dẹt0.5 mét
Lon thiếc2 cái
Tấm sắt tây1 cái
Đinh tán rút8 cái
Bộ bu lông lục giác nhiều cỡ1 cái
Đai ốc lục giác1 cái
Khối gỗ cứng1 cái
Chanh vàng2 cáiCông cụ cần thiết:
Cưa sắt
Máy khoan pin
Bộ mũi khoan
Giũa (giũa tay)
Bộ giũa kim
Ê tô bàn nguội
Kéo cắt tôn
Búa
Bộ súng tán đinh rút
Mỏ lết
Dao bếp
Cân nhà bếp điện tử
Cốc uống nước
Găng tay da bảo hộ5
5
A squeezer that lets seeds through, clogs or sprays
A squeezer that lets seeds through, clogs or sprays
Shears-cup lemon squeezer troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**Thomas Reece and Arthur Clarke** of Philadelphia, Pennsylvania, received US 61,251, dated 15 January 1867. The cups could be metal, galvanized, or wood tinned against the acid; the peculiar shape of cup A with its recess kept the squeezer from clogging or choking. Their claim is the two hinged handles with the two cups, one with a slotted recess and the other with a flange.
**Honest limits.** Tin cans and flat bar stand in for their made-up cups and handles. The notebook ignores friction; its forces and lengths are examples. Your seed count and juice are the result.
Vật liệu
8- 0.5 métTạm thời
- 2 cáiTạm thời
- 1 cáiTạm thời
- 8 cáiTạm thời
- Tạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- 2 cáiTạm thời
Công cụ yêu cầu
14- Tạm thời
- 1 vendor sell this, none ship to you yetTạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
Bản thiết kế này làm ra
Blueprint liên quan
Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc
CC0 Phạm vi công cộng
Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.
Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.



