NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO

The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles
Water dribbled onto the back of a brush stays in the bristles and never reaches the surface being washed.
Frank L. Brinn of Milwaukee received US 840,604, patented 8 January 1907, for a fountain brush in which "the fluid may be delivered to the longitudinal central portion of the brush in a sheet, which when the fluid is turned on at full head will serve to separate the bristles and flush the surface to be washed": slots through the block narrow toward the bristles, fed from a cylinder on top through a tubular handle, with a cup on the handle to catch what runs down.
This rung works out how the taper speeds the sheet, then cuts the slots in a scrub brush, plumbs it and compares full flow with throttled flow.
Trung cấp
About 4 hours
Hướng dẫn
1
1
Sheet speed from the slot
Sheet speed from the slot
Đang tải sổ tay Jupyter…
2
2
Water through a brush's back before it
Water through a brush's back before it
The embedded blueprint jets or soaks water through openings in a brush's back. Brinn shapes the openings into tapered slots so the water leaves as a sheet.
3
3
Read US 840,604
Read US 840,604
"By opening the valve at 3 to its full capacity a sheet of water will be discharged which will separate the bristles and effectively flush the surface to be washed, whether the bristles are in contact with such surface or not. By partially closing the valve at 3 the sheets of water escaping through the openings 18 are broken up by the bristles, and the water thus becomes distributed throughout the brush."
4
4
Cut the slots
Cut the slots
On the scrub brush's top mark two slots 60 × 8 mm, 90 mm apart on the centre line. Drill a row of holes in each and cut it through with the coping saw.
Vật liệu cho bước này:
Bàn chải cọ1 cáiCông cụ cần thiết:
Ê tô bàn nguội
Máy khoan pin
Bộ mũi khoan
Cưa lọng tay
Bút dạ không xoá
Thước kẻ5
5
Taper the slots
Taper the slots
Pare each slot with chisels so its long sides close to about 1.5 mm at the bristle face and its ends open out to 70 mm. Trim the bristles along the slot line.
Công cụ cần thiết:
Bộ đục gỗ
Búa
Thước cặp điện tử 6 inch
Dao rọc thủ công6
6
Make the manifold
Make the manifold
Cut 160 mm of 22 mm copper tube and cap both ends with fittings. File a 4 mm slot along its underside over both brush slots. Fit a tee in its middle for the handle.
Vật liệu cho bước này:
Ống đồng1 cái
Phụ kiện đồng thau1 cáiCông cụ cần thiết:
Dao cắt ống
Giũa (giũa tay)
Mỏ lết7
7
Seat the manifold
Seat the manifold
Bed the manifold on the brush in silicone over a rubber gasket and strap it down with an aluminium strip and four wood screws.
Vật liệu cho bước này:
Tấm cao su1 cái
Tấm nhôm1 cái
Vít gỗ #8 x 1"1 cáiCông cụ cần thiết:
Kéo cắt tôn
Bộ tua vít
Dao rọc thủ công8
8
Handle, valve and drip cup
Handle, valve and drip cup
Fit 1.2 m of 15 mm copper tube to the tee, with a ball valve and hose connector at its top. Slide a small tin can, holed and sealed with silicone, onto the handle as a drip cup, and fit a short copper spout low on its side.
Vật liệu cho bước này:
Ống đồng1 cái
Van bi1 cái
Phụ kiện đồng thau1 cái
Băng làm kín ren PTFE1 cái
Lon thiếc1 cáiCông cụ cần thiết:
Dao cắt ống
Mỏ lết
Máy khoan pin
Bộ mũi khoan9
9
The patent drawing
The patent drawing
US 840,604 drawing sheet, public domain (expired patent).

10
10
Full flow against throttled
Full flow against throttled
Connect the garden hose. With the valve fully open, hold the brush 2 cm off a board and watch the sheet part the bristles; then close it half and watch the water spread through them. Time a litre into the jug each way.

Vật liệu cho bước này:
Vòi tưới vườn1 cái
Nước1 cáiCông cụ cần thiết:
Ca đong
Đồng hồ bấm giờ
Thước kẻ11
11
A sheet that sprays, sputters or leaks
A sheet that sprays, sputters or leaks
Sheet-of-water fountain brush troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Frank L. Brinn**, a citizen of Canada residing in Milwaukee, filed US 840,604 on 20 February 1905; it was patented 8 January 1907. His cylinder is held to the block by a plate with packing and screws, its slots feeding the slot-apertures; the handle's end carries a rubber sheath and the valve; the cup, with its spout, collects the water instead of letting it run down the handle when the brush is raised.
**Honest limits.** A slotted copper tube stands in for his cylinder, and a tin can for his cup. The notebook treats the sheet as uniform. What you see on the board is the result.
Vật liệu
12- 1 cáiTạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- 2 cáiTạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- Tạm thời
- 1 cáiTạm thời
- Vòi tưới vườnHoa hồng 10%1 cáiTạm thời
- 1 cáiTạm thời
Công cụ yêu cầu
17- Tạm thời
- 1 vendor sell this, none ship to you yetTạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
Blueprint liên quan
Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc
CC0 Phạm vi công cộng
Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.
Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.


