NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
Whirl-Cone Splash-Guard Churn: A Whirl Feeds Air to a Cone, a Funnel Keeps the Cream In
Karen

Tạo bởi

Karen

6. tháng Mười 2026SE
32
0
0
0
0

Whirl-Cone Splash-Guard Churn: A Whirl Feeds Air to a Cone, a Funnel Keeps the Cream In

Young set out to mingle "a large quantity of air" with the milk and to stop it "splashing out of the churn without interfering with the free action of the dasher." John Young of West Galway, New York, received US 7,046, dated 22 January 1850, for an atmospheric churn: a geared spindle carrying a flat plate at its foot, an inverted conical vessel open at its top with wings on its rim, inverted channels on the plate leading out from the cone, and a spiral wing up the spindle. A loose inverted funnel on brackets near the top of the tub, with a small disk on the spindle partly closing its hole, returns whatever is thrown up. This rung looks at the whirl, then prints the cone dasher, spiral wing, funnel and disk, fits them in a bucket, and makes butter.
Trung cấp
About 4 hours, plus printing

Hướng dẫn

1

The whirl

Đang tải sổ tay Jupyter…
2

Air thrown out through channels before it

The embedded blueprint draws air down a hollow stem into radial channels. Young lets the cream's whirl bring the air down into an open cone instead.
3

Read US 7,046

"When the churn is supplied with milk and the dasher is rapidly turned by the application of power to the handle of the crank, the whole mass of milk is put in motion and a whirl is created around the spindle, through this whirl the air descends into the conical vessel D, from which it is discharged centrifugally through the channels g, g, and thus mingled with the milk."
4

Print the parts

Print the cone dasher in one piece (/uploads/blueprints/whirl-cone-splash-guard-churn-cone-dasher.stl): plate, open cone with rim wings, four inverted channels and a spider to the spindle. Print the spiral wing (/uploads/blueprints/whirl-cone-splash-guard-churn-spiral-wing.stl), the splash funnel (/uploads/blueprints/whirl-cone-splash-guard-churn-splash-funnel.stl), which needs a 200 mm bed, the disk (/uploads/blueprints/whirl-cone-splash-guard-churn-disk.stl) and the crank arm (/uploads/blueprints/whirl-cone-splash-guard-churn-crank-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.

Vật liệu cho bước này:

Sợi in PETGSợi in PETG1 cái

Công cụ cần thiết:

Máy in 3D sợi nhựa (FDM)Máy in 3D sợi nhựa (FDM)
5

Spindle and dasher

Slide the cone dasher, then the spiral wing, onto a 10 mm square hardwood spindle and glue them. Stand the spindle in a seat drilled in the centre of a food-grade bucket's floor.

Vật liệu cho bước này:

Chốt gỗ cứngChốt gỗ cứng1 cái
Keo dán gỗKeo dán gỗ1 cái
Xô 20 lítXô 20 lít1 cái

Công cụ cần thiết:

Máy khoan pinMáy khoan pin
Bộ mũi khoanBộ mũi khoan
Cưa tayCưa tay
6

Funnel, disk and crank

Screw three small wooden brackets inside the bucket 70 mm below the rim and set the funnel loosely on them, point down, the spindle through its hole. Glue the disk on the spindle just above the funnel's hole. Pass the spindle through a plywood lid and glue the crank arm and a dowel handle on top.

Vật liệu cho bước này:

Khối gỗ cứngKhối gỗ cứng1 cái
Vít gỗ #8 x 1"Vít gỗ #8 x 1"1 cái
Tấm gỗ dánTấm gỗ dán1 cái
Keo dán gỗKeo dán gỗ1 cái

Công cụ cần thiết:

Cưa tayCưa tay
Máy khoan pinMáy khoan pin
Bộ tua vítBộ tua vít
7

The build in 3D

FreeCAD model of this build, not of the patent: the bucket cut away to show the plate with its open cone and inverted channels, the spiral wing, the loose funnel near the top and the disk on the spindle.
Tệp thiết kếBLENDCC0 - Free
8

Spin and make butter

Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 3 litres. Crank fast enough to raise a whirl round the spindle; time until the butter comes. Lift the funnel out before pouring off the buttermilk. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Bước 8 - Image 1

Vật liệu cho bước này:

Kem tươi béoKem tươi béo3000 ml
Muối biển hạt thôMuối biển hạt thô1 cái
NướcNước1 cái

Công cụ cần thiết:

Nhiệt kế đầu dò cắm sẵnNhiệt kế đầu dò cắm sẵn
Đồng hồ bấm giờĐồng hồ bấm giờ
Cân nhà bếp điện tửCân nhà bếp điện tử
Tô trộn thép không gỉ (lớn)Tô trộn thép không gỉ (lớn)
9

No whirl, cream on the lid

Whirl-cone splash-guard churn troubleshooting.

Flow

Loading...
10

History and honest limits

**John Young** of West Galway, Fulton County, New York, received US 7,046, dated 22 January 1850. A pinion on the spindle geared into a wheel on the cover turned by the crank; the cone and channels came off the spindle by buttons or screws for cleaning; filled very full, the wings on the cone's rim kept its mouth open to the air. He claimed the combination of the inverted vessel H and the disk i on the dasher's stem to prevent the cream splashing out at the lid. **Honest limits.** Our crank turns the spindle directly, without his wheel and pinion, so the whirl may be weaker; printed parts and a bucket stand in for his. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.

Vật liệu

10

Công cụ yêu cầu

9

Tệp thiết kế

1

Bản thiết kế này làm ra

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...