NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
Woven Wire Screen Cloth: Hardened Crimped Steel Rods Locked by Driven Straight Rods (Robins, US 2,154,530, 1939)
Charlie

Tạo bởi

Charlie

31. tháng Mười 2026DE
0
0
0
0
0

Woven Wire Screen Cloth: Hardened Crimped Steel Rods Locked by Driven Straight Rods (Robins, US 2,154,530, 1939)

Screen cloth for gravel and stone wears out fast unless the steel is hard, but hard steel cracks when it is bent in weaving. Robins crimps the rods first, hardens them, and lays them up in layers without bending; straight hardened rods driven in endwise lock the whole panel under spring pressure. Result: coarse screen cloth, openings 5/8 in and up, hardened to as much as 60 Rockwell C; it lasted about twice as long. Source: Robins, US 2,154,530 (1939). He names only steel; a high-carbon steel is ours, since only a hardenable steel reaches 60 Rockwell C. Not given: crimp pitch, hardening heat and quench. Picture drawn by Youblob.
Nâng cao
Factory process

Hướng dẫn

1

Crimp the rods

Cut steel rods, about 3/16 in diameter or more, to length and press-crimp three sets of them between dies. Keep a fourth set straight (no more than a quarter of all rods).

Vật liệu cho bước này:

Dây thép cacbon cao cán nóngDây thép cacbon cao cán nóng1 as required

Công cụ cần thiết:

Máy dậpMáy dập
2

Harden all the rods

Heat-harden the crimped and the straight rods before assembly; crimping first spares the dies. Robins reached 60 Rockwell C. Heat and quench: not given.

Công cụ cần thiết:

Lò muffleLò muffle
Thùng tôi nướcThùng tôi nước
3

Lay up three crimped sets

Lay crimped set 1 in parallel on a table; lay set 3 across it, bends in register; lay set 2 parallel to set 1 on top, its bends opposite. Openings about 5/8 in or more.

Công cụ cần thiết:

Bàn thợBàn thợ
4

Drive in the straight rods

Drive the straight rods endwise, above set 2 and below set 1, alternating with set 3. They lock the panel by spring pressure without bending any rod for good; pulled out again, worn rods can be replaced.

Công cụ cần thiết:

Búa tạBúa tạ

Vật liệu

1

Công cụ yêu cầu

5

Blueprint liên quan

Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...