Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Crosshead Dasher Churn: Dashers Hinged to a Rising Crosshead Slide Their Outer Ends Up Inclined Grooves, Counter-Dashers Above
Buttercup

Yenziwe ngu-

Buttercup

11. uLwezi 2026IE
5
0
0
0
0

Crosshead Dasher Churn: Dashers Hinged to a Rising Crosshead Slide Their Outer Ends Up Inclined Grooves, Counter-Dashers Above

Harry Abbott of North Huron, New York, received US 28,723, dated 19 June 1860, for a churn. In a long box a cross-head in the middle is raised and lowered by a lever; a frame dasher of rods is hinged to each side of it, its outer end sliding in a groove in the box's sides that slopes up inward, so the dashers' inner ends rise and fall while their outer ends move in and out. Above each, a dasher hinged to the box's end works against it and keeps the cream from splashing up. The patent gives no sizes; every size here is ours.
Osezingeni eliphezulu
About 3 days

Imiyalelo

1

Inner ends up and down, outer ends in and out

Ilayisha incwadi ye-Jupyter…
2

A hinged dasher in a long box, four months before

Cunningham swings one dasher from one end. Abbott lifts two from the middle and guides their outer ends in grooves.
3

Read US 28,723

"Arranged thus, the lower dashers E, E, have a compound motion; the inner ends being raised and lowered nearly vertically, while the outer ends are guided in and out nearly horizontally. The milk, or cream, passing through the rods g, g, of the dashers E, E, is violently and effectively agitated; while the rods o, o, of the auxiliary dashers, which have opposite and antagonistic motions, being arranged at right angles to the rods g, g, effectively break the currents, and allay the agitation on the surface."
4

Body A, legs a and grooves b and i

From 20 mm hardwood board make a box 600 x 260 mm inside and 300 deep, glued and screwed, its inside joints sealed with silicone sealant, on four pine legs 480 mm long. Before assembling, rout in each side a vertical groove b 50 mm wide and 10 deep in the middle, and near each end an inclined groove i 14 mm wide and 10 deep, rising inward at 25 degrees from 45 mm above the floor and running into the groove b's path at its top, so the dashers lift out. Cut a lid with a 24 mm square hole in the middle.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile4 izicucu
Amapulangwe omphayiniAmapulangwe omphayini2 izicucu
Iglu LokhuniIglu Lokhuni1 ucezu
Izikulufu zokhuniIzikulufu zokhuni40 izicucu
Isivalo Se-siliconeIsivalo Se-silicone1 ucezu

Amathuluzi adingekayo:

Isaha letafulaIsaha letafula
I-router yokhuniI-router yokhuni
IphrothraktaIphrothrakta
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isibambo sensikaIsibambo sensika
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
Ithephu LokulinganisaIthephu Lokulinganisa
5

Cross-head B and dashers E

Cut a hardwood cross-head 50 x 40 mm, 276 long, its ends fitting the grooves b. For each dasher make a frame of two hardwood side bars 16 x 50 mm, 240 long between pins, and ends f, with five 12 mm stainless rods g across it; fix a 10 mm stainless pin across its outer end, standing out 8 mm each side as the bearings h, and hinge its inner end to the cross-head with a 8 mm stainless pin and split pins, at d.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Insimbi engagqwali eyindukwanaInsimbi engagqwali eyindukwana4 izicucu
Iglu LokhuniIglu Lokhuni1 ucezu
Iphini elinemilenze emibiliIphini elinemilenze emibili4 izicucu

Amathuluzi adingekayo:

Isaha letafulaIsaha letafula
Isethi yezisebenzi zokhuniIsethi yezisebenzi zokhuni
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isaha SensimbiIsaha Sensimbi
Izinsimbi zokuhlikihla (ezesandla)Izinsimbi zokuhlikihla (ezesandla)
6

Auxiliary dashers G

Make each auxiliary dasher as a frame 230 mm long with four hardwood rods o, 8 mm thick, along its length, at right angles to the rods g below. Hinge its outer end to the box's end 200 mm up with a staple over a hook, held by a button. Let its middle rod run on past its inner end and through a screw eye on the dasher E's inner end, so G's inner end follows E's.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu
Iglu LokhuniIglu Lokhuni1 ucezu
Isikulufu esinendandathoIsikulufu esinendandatho2 izicucu
Ingwegwe nesoIngwegwe neso2 izicucu
Izikulufu zokhuniIzikulufu zokhuni8 izicucu

Amathuluzi adingekayo:

Isaha letafulaIsaha letafula
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
7

Rod C, lever D and fulcrum c

Cut a hardwood rod C 24 mm square, 420 long, and fix its foot in the cross-head's middle. Bolt a hardwood link c 90 mm between holes to a block on the outside of one end of the box, near the top. Cut a hardwood lever D, 720 mm long with a handle shaped at one end, and bolt it to the top of rod C and, 360 mm from that pin, to the link's top.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile2 izicucu
Ibhawoti elinekhanda eliyindilingaIbhawoti elinekhanda eliyindilinga3 izicucu
Inati Yokukhiya EnenayiloniInati Yokukhiya Enenayiloni3 izicucu
Iglu LokhuniIglu Lokhuni1 ucezu
Izikulufu zokhuniIzikulufu zokhuni4 izicucu

Amathuluzi adingekayo:

Isaha letafulaIsaha letafula
Isaha Le-jigsawIsaha Le-jigsaw
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isipanela esilungisekayoIsipanela esilungisekayo
8

The build in 3D

FreeCAD model of this build, one side left off: the cross-head in its middle grooves, the two rod dashers hinged to it with their outer bearings in the inclined grooves, the auxiliary dashers above hinged at the ends, the rod C, the lever D and its swinging fulcrum link.
Ifayela LomklamoBLENDCC0 - Free
9

Churn

Pour about 15 litres of heavy cream at about 15 °C, checked with the thermometer, into the box and put on the lid. Work the lever up and down steadily, about 120 mm at the cross-head, timing it. When the butter comes, take off the lid, unhook the auxiliary dashers, lift the cross-head and dashers out by the grooves, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Izinto zokwakha zalesi sinyathelo:

Ukhilimu ojiyileUkhilimu ojiyile15 l
Usawoti Wolwandle OmkhuluUsawoti Wolwandle Omkhulu1 ucezu
AmanziAmanzi1 ucezu

Amathuluzi adingekayo:

Ithemomitha enenaliti eshiywa ngaphakathiIthemomitha enenaliti eshiywa ngaphakathi
Iwashi Lokumisa IsikhathiIwashi Lokumisa Isikhathi
Isikali Sedijithali SasekhishiniIsikali Sedijithali Sasekhishini
Isitsha esikhulu sokuxuba sensimbi engagqwaliIsitsha esikhulu sokuxuba sensimbi engagqwali
10

Troubleshooting

Crosshead dasher churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Harry Abbott** of North Huron, Wayne County, New York, US 28,723, 19 June 1860 (signed 7 April 1860), "Churn". He claimed the dashers E guided by the vertical and inclined grooves, with the counter-acting dashers G. He gives no sizes and allows any equivalent way of working the cross-head; every size, the groove angle and the stroke here are ours.

Izinto

15

Amathuluzi Adingekayo

17

Amafayela omklamo

1

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...