UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Blinking an LED with LilyPad Arduino
Ed

Yenziwe ngu-

Ed

13. uNtulikazi 2026FI
38
0
0
0
0

Blinking an LED with LilyPad Arduino

Step up from a plain sewn circuit to a sewable computer. The LilyPad Arduino is a washable microcontroller you program from your PC, then run on a coin cell — so your fabric can blink, fade and react on its own. This project sews an LED to the board and uploads the classic 'blink' sketch: the gateway to every sensor-driven wearable that follows.

Ophakathi
1 hour

Imiyalelo

1

Sew the LilyPad Arduino and an LED

Sew a LilyPad Arduino Simple board and a LilyPad LED onto felt with conductive thread: the LED's + tab to numbered pin 5, and the LED's - tab to the board's - tab. Loop 3–4 times through each hole, trim tails, and keep the two lines from crossing.

Izinto zokwakha zalesi sinyathelo:

LilyPad Arduino Simple BoardLilyPad Arduino Simple Board1 ucezu
LilyPad LED - 5 pcsLilyPad LED - 5 pcs1 iphakethe
Conductive Thread - 60g (Stainless Steel)Conductive Thread - 60g (Stainless Steel)1 isipulu
Izinaliti zokuthunga ngesandlaIzinaliti zokuthunga ngesandla1 iphakethe
Ishidi lofelefele woboyaIshidi lofelefele woboya1 ishidi
2

Connect the FTDI programmer

Plug a LilyPad FTDI Basic Breakout onto the board's 6-pin programming header (line up GND to GND, DTR to DTR) and connect it to your computer with a USB cable. Install the free Arduino IDE, then choose the LilyPad Arduino board and the FTDI's serial port under Tools.

Izinto zokwakha zalesi sinyathelo:

LilyPad FTDI Basic Breakout - 5VLilyPad FTDI Basic Breakout - 5V1 ucezu
SparkFun Cerberus USB Cable - 1.8 meterSparkFun Cerberus USB Cable - 1.8 meter1 ucezu

Amathuluzi adingekayo:

Ikhompyutha Ene-Arduino IDEIkhompyutha Ene-Arduino IDE
3

Upload the blink sketch

Paste this sketch into the Arduino IDE and click Upload. It flashes the LED on pin 5 on and off twice a second.

lilypad_blink.inoarduino
// Blink an LED sewn to a LilyPad Arduino
// The LED's + tab is stitched to pin 5, its - tab to the board's - (GND).

const int LED_PIN = 5;   // LilyPad LED sewn to pin 5

void setup() {
  pinMode(LED_PIN, OUTPUT);   // pin 5 drives the LED
}

void loop() {
  digitalWrite(LED_PIN, HIGH); // LED on
  delay(500);                  // wait half a second
  digitalWrite(LED_PIN, LOW);  // LED off
  delay(500);                  // wait half a second
}

// TRY THIS:
// - delay(100) for fast blinking, delay(2000) for slow
// - different ON and OFF times: HIGH delay(800), LOW delay(200)
4

Go wireless on a coin cell

Unplug the FTDI. Sew a LilyPad coin-cell battery holder to the board — + tab to +, - tab to - — and drop in a CR2032. Switch it on and the LED blinks on its own, no computer attached. Your fabric now runs its own program.

Izinto zokwakha zalesi sinyathelo:

LilyPad Coin Cell Battery Holder - w/Switch - 20mmLilyPad Coin Cell Battery Holder - w/Switch - 20mm1 ucezu
Ibhethri lohlamvu CR2032Ibhethri lohlamvu CR20321 ucezu
5

Experiment

Re-attach the FTDI and change the sketch: adjust the delays for a heartbeat rhythm, or sew a second LED to another pin and blink them in turn. This is the base every LilyPad sensor project builds on.

Izinto

9

Amathuluzi Adingekayo

2
Isamba Esilinganiselwe
Lokho umenzi akuthenga. Izinto ezikhonjiswa ngaphandle kwentengo uzithola lapho uzithenga khona.
$88.32

Ama-blueprint ahlobene

Lama-blueprint abelana ngolwazi — amasu, izinto noma izimiso

Sewing a LilyPad LED Circuit

Sewing a LilyPad LED Circuit

ngu-EdFI

Kwedijithali

35
0
0
0
0
0
Blinking LED — Your First Arduino Project
BLUEPRINT NFT

Blinking LED — Your First Arduino Project

ngu-Admiral OOMNO

Kwedijithali

515
2
1
7
0
0

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...