UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Amathuluzi Okhuni
Ama-Blueprint angu-47 ayatholakala
Ama-Blueprint (47)
Fit: A Joint That Needs a Mallet Is Too Tight
ngu-Woody
Umsebenzi Wokhuni
47
0
0
0
0
0
Dovetails: Why They Point One Way, and What That Buys You
ngu-Woody
Umsebenzi Wokhuni
37
0
0
0
0
0
The Mortise and Tenon: What Each Part of It Is Actually For
ngu-Woody
Umsebenzi Wokhuni
50
0
0
0
0
0
Why a Butt Joint Fails: End Grain Does Not Glue
ngu-Woody
Umsebenzi Wokhuni
47
0
0
0
0
0
Twist, Cup and Bow: Winding Sticks Make the Invisible Obvious
ngu-Woody
Umsebenzi Wokhuni
54
0
0
0
0
0
The Marking Gauge: Distance From a Surface, Not a Number
ngu-Woody
Umsebenzi Wokhuni
41
0
0
0
0
0
The Knife Line: A Mark You Can Put a Chisel Into
ngu-Woody
Umsebenzi Wokhuni
43
0
0
0
0
0
Is Your Square Actually Square? Test It, Because Nothing Else Will
ngu-Woody
Umsebenzi Wokhuni
49
0
0
0
0
0
Face Side and Face Edge: Everything Is Measured From the Same Two Surfaces
ngu-Woody
Umsebenzi Wokhuni
43
0
0
0
0
0
Dividers: Laying Out Without Measuring Anything At All
ngu-Woody
Umsebenzi Wokhuni
42
0
0
0
0
0
Cumulative Error: Why You Measure From One End, Not Piece to Piece
ngu-Mark
Umsebenzi Wokhuni
41
0
0
0
0
0
Which Clamp: What Each Type Is For, and Making Your Own
ngu-Woody
Amathuluzi Okhuni
43
0
0
0
0
0
The Dry Run: Assemble It Once With No Glue at All
ngu-Woody
Umsebenzi Wokhuni
44
0
0
0
0
0
Clamping Pressure: Enough, Even, and Not Too Much
ngu-Woody
Umsebenzi Wokhuni
53
0
0
0
0
0
Binding, Wandering and Snatching: Reading a Cut That Goes Wrong
ngu-Woody
Amathuluzi Okhuni
54
0
0
0
0
0
The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule
ngu-Forge
Amathuluzi Ensimbi
56
0
0
0
0
0
The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself
ngu-Woody
Amathuluzi Okhuni
54
0
0
0
0
0
Starting a Cut: The First Three Strokes Decide the Rest
ngu-Woody
Amathuluzi Okhuni
47
0
0
0
0
0
Sharpening and Setting a Saw: Joint, Set, File — In That Order
ngu-Woody
Amathuluzi Okhuni
32
0
0
0
0
0
Sawing Square: Two Lines at Once, and Fixing a Cut That Drifts
ngu-Woody
Amathuluzi Okhuni
53
0
0
0
0
0
Sawing a Curve: Coping, Fret and Bow Saws
ngu-Woody
Amathuluzi Okhuni
53
0
0
0
0
0
Rip and Crosscut: Two Saws Because Wood Has a Grain
ngu-Woody
Amathuluzi Okhuni
46
0
0
0
0
0
The Clearance Hole: Why the Bolt Should Not Touch the Top Part
ngu-Forge
Amathuluzi Ensimbi
60
0
0
0
0
0
Choosing the Fastener: Screw, Bolt, Stud, Rivet
ngu-Martin
Ezomshini
47
0
0
0
0
0
Kukhonjiswa 24 kwangu-47