UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Fits: Clearance, Transition and Interference — the Difference Is Microns
A shaft that slides into a hole and a shaft that has to be pressed in can differ in diameter by less than the thickness of a human hair. Which of those you have is decided by a few microns, and the difference in behaviour is total.
A CLEARANCE fit always has a gap: the parts assemble by hand and can move. An INTERFERENCE fit always has the shaft larger than the hole: the parts must be forced together and then grip each other permanently. A TRANSITION fit may be either, depending on where the two parts happen to fall in their tolerances.
This is why a bearing can spin on its shaft, or crack its outer ring, or work perfectly — all from the same drawing and the same parts bin. The fit is the design decision, and it is made in numbers before anything is cut.
Ophakathi
3 hours
Imiyalelo
1
1
Measure both parts, and measure them properly
Measure both parts, and measure them properly
You cannot choose a fit without knowing what you have. Measure the shaft and the bore with a micrometer or a good caliper, at several places along their length and at several angles round them.
Several angles matters because nothing is perfectly round. A shaft that reads 19.98 mm one way and 20.02 mm at ninety degrees is out of round by 0.04 mm, which is larger than most fits — and averaging the two hides it.
Let both parts reach the same temperature first. Steel expands about 11 microns per metre per degree, so a 50 mm part handled for a minute can grow by more than the fit you are trying to measure. Warm hands are a real error here.
Izinto zokwakha zalesi sinyathelo:
I-shaft yensimbi engu-30 mm1 ucezuAmathuluzi adingekayo:
I-Vernier Caliper
I-Caliper Yedijithali Yamayintshi Ayi-62
2
The arithmetic, and what each fit is for
The arithmetic, and what each fit is for
Ilayisha incwadi ye-Jupyter…
Izinto zokwakha zalesi sinyathelo:
I-shaft yensimbi engu-30 mm1 ucezu
Ball Bearing - Non-Flanged (8mm Bore, 22mm OD)1 ucezuAmathuluzi adingekayo:
I-Vernier Caliper
Ikhompyutha Yasetafuleni
Isibali3
3
Temperature is a tool, not just an error
Temperature is a tool, not just an error
Heat the outer part and it grows; chill the inner part and it shrinks. Do both and an interference fit can be assembled by hand, then locks as the temperatures equalise.
Steel expands about 11 microns per metre per degree Celsius, so a 100 mm bore heated by 100 degrees grows roughly 0.11 mm — far more than any normal interference. An oven at 120 degrees, or a freezer for the shaft, is usually enough.
Never heat a bearing above about 120 degrees. Above that the hardened rings begin to temper and lose hardness permanently, and a blowtorch anywhere near a bearing ruins it in seconds. Induction heaters and hot oil baths exist precisely because the temperature has to be controlled.
Izinto zokwakha zalesi sinyathelo:
I-shaft yensimbi engu-30 mm1 ucezuBall Bearing - Non-Flanged (8mm Bore, 22mm OD)1 ucezuAmathuluzi adingekayo:
I-Caliper Yedijithali Yamayintshi Ayi-6
Amagilavu Erabha Ye-Nitrile4
4
Surface finish and roundness are part of the fit
Surface finish and roundness are part of the fit
A measured diameter is an average over a surface that has peaks and valleys. Press two rough surfaces together and the peaks flatten, so the effective interference is less than the measured one — often by 2 to 5 microns on ordinary turned work.
That is why bearing seats are ground rather than turned. It is not fussiness: a rough seat loses a significant fraction of a 15 micron interference to flattened peaks the first time the joint is loaded, and then the bearing creeps.
Roundness matters as much. A bore that is 0.03 mm oval will grip a round shaft at two points and leave gaps at ninety degrees, so the pressure is concentrated rather than shared — which distorts the bearing ring and takes the internal clearance with it.
Izinto zokwakha zalesi sinyathelo:
I-shaft yensimbi engu-30 mm1 ucezuAmathuluzi adingekayo:
Isikhombisi Se-dialI-Vernier Caliper
Isethi yezilinganiso zesikhalaIzinto
2- 1 ucezuIsibambeli
- Ball Bearing - Non-Flanged (8mm Bore, 22mm OD)ikhomishini engu-10%1 ucezu$1.27
Amathuluzi Adingekayo
7- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
Isamba Esilinganiselwe
Lokho umenzi akuthenga. Izinto ezikhonjiswa ngaphandle kwentengo uzithola lapho uzithenga khona.
Ama-blueprint ahlobene
Lama-blueprint abelana ngolwazi — amasu, izinto noma izimiso
CC0 Isizinda Somphakathi
Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.
Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.