Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Gate-and-Wing Dasher Churn: A Rising Gate Swings Two Wings Down
English
YourGrandma

Yenziwe ngu-

YourGrandma

6. uMfumfu 2026IS
37
0
0
0
0

Gate-and-Wing Dasher Churn: A Rising Gate Swings Two Wings Down

King set out to produce "a combination of a variety of motions in the dashers" by which "the labor in the process of churning is lessened." Charles King of Scipio, New York, received US 4,449, dated 4 April 1846, for a churn-dasher in an oblong box with a semicircular bottom. A shaft runs lengthwise at the centre of the bottom's circle. A handle on a cross-piece lifts a vertical gate dasher whose slotted posts embrace the shaft; two oscillating dashers of triangular head-pieces and slats hang on the shaft, their inner ends tied to the gate's top rail, so their outer ends "perform a segmental motion downward" as the gate rises, and back. This rung works out the wings' swing, then prints the head-pieces, gate and ends, bends a stainless bottom, and makes butter.
Osezingeni eliphezulu
About 6 hours, plus printing

Imiyalelo

1

The wings' swing

Ilayisha incwadi ye-Jupyter…
2

Linked dashers worked by a lever before it

The embedded blueprint links two dashers by bent levers. King links an upright gate and two swinging wings to one handle.
3

Read US 4,449

"The handle n being depressed, the opposite end of the arm or lever g rises, and consequently raises the vertical dasher. In consequence of the inner extremities of the oscillating dashers being attached to the top rail of the vertical dasher, the outer extremities of said dashers perform a segmental motion downward, and vice versa when the handle n is raised."
4

Print the parts

Print two end pieces flat, the gate dasher with its two slotted posts, and four triangular head-pieces, each with a segmental side, slat sockets and an extension for its tie. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.

Izinto zokwakha zalesi sinyathelo:

Ifilamenti ye-PETGIfilamenti ye-PETG1 ucezu

Amathuluzi adingekayo:

Iphrinta ye-3D yentambo (i-FDM)Iphrinta ye-3D yentambo (i-FDM)
5

Print the end

The end, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
6

Print the gate

The gate, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
7

Print the triangular head-pieces

The triangular head-pieces, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
8

Bend the bottom and set the shaft

Cut a 0.5 mm stainless sheet 170 mm wide and about 315 mm long, deburr it, and bend it round a 130 mm form into a U with 55 mm straight sides. Seat it in both end pieces' grooves in silicone. Pass a 12 mm hardwood dowel through both ends at the circle's centre as the shaft.

Izinto zokwakha zalesi sinyathelo:

Ishidi lensimbi engagqwali - 304Ishidi lensimbi engagqwali - 3041 ucezu
Isivalo Se-siliconeIsivalo Se-silicone1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu

Amathuluzi adingekayo:

Isikeli sensimbiIsikeli sensimbi
Ithuluzi lokususa amabhadiIthuluzi lokususa amabhadi
Isando serabhaIsando serabha
Ama-clampAma-clamp
Ithephu LokulinganisaIthephu Lokulinganisa
9

Dashers, lever and handle

Slide the gate's slotted posts over the shaft, and between them hang two pairs of head-pieces on the shaft, one pair each side; glue 5 mm dowel slats into their sockets to make the two oscillating dashers. Tie each head-piece's extension to an end of the gate's top rail with a short pine slat on screws. Stand a pine post at one end, pivot a lever on it, hang a pitman from the lever to the gate's middle, and fit the handle.

Izinto zokwakha zalesi sinyathelo:

Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu
Ipulangwe lomphayiniIpulangwe lomphayini1 ucezu
Izikulufu zomshiniIzikulufu zomshini1 ucezu
Inathi Yezinhlangothi EziyisithuphaInathi Yezinhlangothi Eziyisithupha1 ucezu
Iglu LokhuniIglu Lokhuni1 ucezu
Isikulufo sokhuni #8 x 1"Isikulufo sokhuni #8 x 1"1 ucezu

Amathuluzi adingekayo:

Isaha SesandlaIsaha Sesandla
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
Isipanela esilungisekayoIsipanela esilungisekayo
10

The patent drawing

US 4,449 drawing sheet, public domain (expired patent).
Isinyathelo 10 - Image 1
11

Work the handle and make butter

Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 700 ml. Work the handle steadily up and down; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.

Izinto zokwakha zalesi sinyathelo:

Ukhilimu ojiyileUkhilimu ojiyile700 ml
Usawoti Wolwandle OmkhuluUsawoti Wolwandle Omkhulu1 ucezu
AmanziAmanzi1 ucezu

Amathuluzi adingekayo:

Ithemomitha enenaliti eshiywa ngaphakathiIthemomitha enenaliti eshiywa ngaphakathi
Iwashi Lokumisa IsikhathiIwashi Lokumisa Isikhathi
Isikali Sedijithali SasekhishiniIsikali Sedijithali Sasekhishini
Isitsha esikhulu sokuxuba sensimbi engagqwaliIsitsha esikhulu sokuxuba sensimbi engagqwali
12

A gate that jams, wings that scrape

Gate-and-wing dasher churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Charles King** of Scipio, Cayuga County, New York, received US 4,449, dated 4 April 1846. Two legs at one end rose above the box to carry the cross-piece's gudgeons. The head-pieces "need not be of one entire piece, but may be made with two arms ... so as to produce what may be called twin-dashers." He claimed "the combination of the vertical dasher with the oscillating dashers." **Honest limits.** Stainless sheet and printed parts stand in for his wooden box and dashers. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.

Izinto

12

Amathuluzi Adingekayo

15

Amafayela omklamo

3

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...