Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Window-Blind Dasher Churn: Slats Set Slantwise Through the Staff, Turned Back and Forth by a Cord From a Swinging Disk
Buttercup

Yenziwe ngu-

Buttercup

11. uLwezi 2026IE
5
0
0
0
0

Window-Blind Dasher Churn: Slats Set Slantwise Through the Staff, Turned Back and Forth by a Cord From a Swinging Disk

Samuel A. Kerr of Arbor Hill, Virginia, received US 28,757, dated 19 June 1860, for a churn. Flat slats pass slantwise through an upright staff, one above another like the slats of a window blind. A cord from a disk swung back and forth by a handle turns the staff to and fro: the slats on one side throw the cream up, those on the other throw it down, and it passes between them from side to side. Turned gently, the overlapping slats gather the butter. A funnel in the lid lets air in. The patent gives no sizes; every size here is ours.
Ophakathi
About 2 days, plus printing

Imiyalelo

1

Slats like a window blind

Ilayisha incwadi ye-Jupyter…
2

Oblique slats that throw the cream, three months before

Embree sets his slats inside a turning barrel. Kerr sets them through a staff turned to and fro.
3

Read US 28,757

"By this oblique arrangement of the blades or slats on a vibrating or turning dasher staff, the cream or milk will, when the staff is rapidly vibrating, be thrown downward, on one side of the staff, and upward, on the other side, at each back or forward movement; and it also will be caused to pass between the slats from one side of the churn to the other."
4

Print the air funnel B

Funnel 80 mm across at its mouth with a 39 mm spout 30 mm long to pass through the lid. PETG, 0.2 mm layers, 4 walls.
Ifayela LomklamoSTLCC0 - Free
5

Dasher C: staff and slats a

Cut a 35 mm square hardwood staff 340 mm long and glue 12 mm stainless spindles into its ends. Cut five hardwood slats 240 x 60 x 8 mm and drill each with four 12 mm holes. Chisel five slots through the staff, each at 45 degrees to it and 45 mm apart from 80 mm above its foot, all sloping the same way, and glue the slats through them, centred, so each slat's lower edge meets the next one's upper edge.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Insimbi engagqwali eyindukwanaInsimbi engagqwali eyindukwana1 ucezu
Iglu LokhuniIglu Lokhuni1 ucezu

Amathuluzi adingekayo:

Isaha letafulaIsaha letafula
Isethi yezisebenzi zokhuniIsethi yezisebenzi zokhuni
IphrothraktaIphrothrakta
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isaha SensimbiIsaha Sensimbi
Iphepha LokugayaIphepha Lokugaya
6

Lid, bar, step and funnel B

Screw a hardwood step 50 x 50 x 8 mm, bored 12.6 mm, to the bucket's floor centre. Cut an HDPE lid to fit the rim with a 26 mm hole over the centre and a 40 mm hole beside it for the funnel. Screw a hardwood bar 510 x 50 x 25 mm across the lid, bored over the centre, reaching 300 mm out past the rim, with a hardwood bracket under its end against the bucket's side. Push the funnel into its hole.

Izinto zokwakha zalesi sinyathelo:

Ibhakede Lamalitha Angu-20Ibhakede Lamalitha Angu-201 ucezu
Ibhulokhi Lokhuni OluqinileIbhulokhi Lokhuni Oluqinile1 ucezu
Ishidi le-HDPEIshidi le-HDPE1 ucezu
Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Izikulufu zokhuniIzikulufu zokhuni10 izicucu
Ifilamenti ye-PETGIfilamenti ye-PETG1 ucezu

Amathuluzi adingekayo:

Iphrinta ye-3D yentambo (i-FDM)Iphrinta ye-3D yentambo (i-FDM)
Isaha Le-jigsawIsaha Le-jigsaw
Isethi yamasaha ezimboboIsethi yamasaha ezimbobo
Isaha letafulaIsaha letafula
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
7

Pulley, disk E, handle F and cord D

Turn or cut a hardwood pulley 60 mm across with a groove and fix it on the staff's top spindle above the bar. Cut a hardwood disk E 200 mm across with a groove round its edge, pivot it on a 12 mm stainless pin in the bar's end, and screw a hardwood handle F with an upright dowel grip across it. Tie a cord to the disk, take it round the pulley once and back to the disk, and tie it tight.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu
Insimbi engagqwali eyindukwanaInsimbi engagqwali eyindukwana1 ucezu
Iglu LokhuniIglu Lokhuni1 ucezu
Izikulufu zokhuniIzikulufu zokhuni4 izicucu
Shaft CollarShaft Collar2 izicucu
IntamboIntambo1 ucezu

Amathuluzi adingekayo:

Isaha Le-jigsawIsaha Le-jigsaw
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isaha SensimbiIsaha Sensimbi
Izinsimbi zokuhlikihla (ezesandla)Izinsimbi zokuhlikihla (ezesandla)
Iphepha LokugayaIphepha Lokugaya
8

The build in 3D

FreeCAD model of this build, the bucket cut open: the staff with its five slantwise slats, the funnel, the bar with its bracket, the pulley, and the disk E with its handle F and the cord.
Ifayela LomklamoBLENDCC0 - Free
9

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the dasher in its step, put on the lid and bar, and swing the handle quickly back and forth, timing it. When the butter comes, swing it slowly and gently to gather it, as the patent says. Lift off the bar and lid, take out the dasher and butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Izinto zokwakha zalesi sinyathelo:

Ukhilimu ojiyileUkhilimu ojiyile8 l
Usawoti Wolwandle OmkhuluUsawoti Wolwandle Omkhulu1 ucezu
AmanziAmanzi1 ucezu

Amathuluzi adingekayo:

Ithemomitha enenaliti eshiywa ngaphakathiIthemomitha enenaliti eshiywa ngaphakathi
Iwashi Lokumisa IsikhathiIwashi Lokumisa Isikhathi
Isikali Sedijithali SasekhishiniIsikali Sedijithali Sasekhishini
Isitsha esikhulu sokuxuba sensimbi engagqwaliIsitsha esikhulu sokuxuba sensimbi engagqwali
10

Troubleshooting

Window-blind dasher churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Samuel A. Kerr** of Arbor Hill, Augusta County, Virginia, US 28,757, 19 June 1860 (signed 9 May 1860), "Churn". He claimed only the manner of arranging the slats on a vibrating or turning staff, not the means of vibrating it. He allows solid or perforated slats and a cord or chain; our slat count, angle and sizes are ours.

Izinto

14

Amathuluzi Adingekayo

16

Amafayela omklamo

2

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...