Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Opposed Spiral Wing Churn: Two Half-Spiral Wings Dash the Cream From End to End
English
Tinny

Yenziwe ngu-

Tinny

7. uMfumfu 2026US
34
0
0
0
0

Opposed Spiral Wing Churn: Two Half-Spiral Wings Dash the Cream From End to End

Enos Page of Streetsboro, Ohio, received US 19,310, dated 9 February 1858, for a cylindrical churn whose shaft carries two wings "like the half of a spiral disk," curving opposite ways on opposite sides of the shaft, so that at every turn the cream moves "suddenly from the end, toward, and past the center." This rung prints the wings, builds the churn and makes butter.
Ophakathi
About 3 hours, plus printing

Imiyalelo

1

Half a spiral each

Ilayisha incwadi ye-Jupyter…
2

A spiral agitator before it

Webster's spiral turns on an upright shaft; Page's two half-spirals on a horizontal one drive the cream end to end.
3

Read US 19,310

"The two wings, F and F', having their spiral curves in opposite directions, or right and left, as seen in Figs. 2 and 3, being placed upon opposite sides of the shaft D, at every revolution of the shaft and wings, causes the milk or cream in the churn, to move suddenly from the end, toward, and past the center of the body of the churn."
4

Print the parts

Print two wings on supports; one is used turned end for end, so the two curve opposite ways. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.

Izinto zokwakha zalesi sinyathelo:

Ifilamenti ye-PETGIfilamenti ye-PETG1 ucezu

Amathuluzi adingekayo:

Iphrinta ye-3D yentambo (i-FDM)Iphrinta ye-3D yentambo (i-FDM)
5

Print the wing

The wing, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
6

Drum and shaft

Lay a round food-grade container about 170 mm across and 180 mm long on its side in a pine cradle, a door in its top. Push both wings onto a 10 mm square hardwood shaft, one from each end, on opposite sides of the shaft, and run it through the container's ends on the axis.

Izinto zokwakha zalesi sinyathelo:

Isitsha sokugcina sezinga lokudlaIsitsha sokugcina sezinga lokudla1 ucezu
Ipulangwe lomphayiniIpulangwe lomphayini1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu
Isivalo Se-siliconeIsivalo Se-silicone1 ucezu

Amathuluzi adingekayo:

Isaha Se-CopingIsaha Se-Coping
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
7

Crank

Glue a pine crank arm and dowel handle on the shaft's end.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe lomphayiniIpulangwe lomphayini1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu
Iglu LokhuniIglu Lokhuni1 ucezu

Amathuluzi adingekayo:

Isaha SesandlaIsaha Sesandla
Ibhola ElingenantamboIbhola Elingenantambo
8

The build in 3D

FreeCAD model of this build: the drum cut open to show the two half-spiral wings on the shaft, each sweeping one end and half the length.
Ifayela LomklamoBLENDCC0 - Free
9

Churn and gather

Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Crank steadily, turning back now and then to clear the wings' backs, as he says; time until the butter comes. Turn slowly to gather it into a ball. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Isinyathelo 9 - Image 1

Izinto zokwakha zalesi sinyathelo:

Ukhilimu ojiyileUkhilimu ojiyile1500 ml
Usawoti Wolwandle OmkhuluUsawoti Wolwandle Omkhulu1 ucezu
AmanziAmanzi1 ucezu

Amathuluzi adingekayo:

Ithemomitha enenaliti eshiywa ngaphakathiIthemomitha enenaliti eshiywa ngaphakathi
Iwashi Lokumisa IsikhathiIwashi Lokumisa Isikhathi
Isikali Sedijithali SasekhishiniIsikali Sedijithali Sasekhishini
Isitsha esikhulu sokuxuba sensimbi engagqwaliIsitsha esikhulu sokuxuba sensimbi engagqwali
10

Troubleshooting

Opposed spiral wing troubleshooting.

Flow

Loading...
11

History and honest limits

**Enos Page** of Streetsboro, Portage County, Ohio, US 19,310, 9 February 1858. His body was zinc or sheet metal nailed to wooden ends. He did not claim spiral dashers forcing the cream alternately in opposite directions; he claimed the wings' arrangement, their radial edges sweeping the ends and their spiral edges each half the length. A container and printed wings stand in for his. FDM prints hold food in their layer lines, so wash well and replace when worn.

Izinto

9

Amathuluzi Adingekayo

9

Amafayela omklamo

2

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...