Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Surface Dash-Wheel Churn: A Fast Fan Skims the Cream Over a Partition on a Parallel-Rule Frame
Buttercup

Yenziwe ngu-

Buttercup

9. uLwezi 2026IE
10
0
0
0
0

Surface Dash-Wheel Churn: A Fast Fan Skims the Cream Over a Partition on a Parallel-Rule Frame

Andrew Patterson of Birmingham, Pennsylvania, received US 23,111, dated 1 March 1859, for a churn whose fan wheel only strikes the surface of the cream. Turned fast through a pulley, it throws the cream over a partition; the cream sinks and comes back under it. The wheel's chamber is also the churn's lid and rests on a jointed frame that works like a parallel rule, so a handle sets the fan to dip about 1/8 in. into whatever quantity of cream is in the box. This rung builds it in pine with a belt-driven printed fan.
Ophakathi
About 8 hours, plus printing

Imiyalelo

1

Setting the rest for the cream you have

Ilayisha incwadi ye-Jupyter…
2

A dasher that adjusts to the tub, before it

Fiester's blades spread to fit his tub. Patterson moves his whole fan up and down to the cream's surface.
3

Read US 23,111

"... the rest o, o, w, v, v, is raised or lowered until when b is placed on it the buckets or fans will dip about one-eighth of an inch into the cream and the crank is turned rapidly in such manner that the wheel shall impel the milk or cream which it strikes in the direction of w".
4

Print the hub

The fan's hub with eight square sockets for the arms. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Ifayela LomklamoSTLCC0 - Free
5

Print the bucket y

A curved bucket for an arm pair's ends. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Ifayela LomklamoSTLCC0 - Free
6

Box a

From 18 mm pine make an oblong box open at the top, 600 x 300 mm and 320 mm deep inside: floor 636 x 336 mm, sides 636 x 320 mm, ends 300 x 320 mm, glued and screwed.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe lomphayiniIpulangwe lomphayini2 izicucu
Iglu LokhuniIglu Lokhuni1 ucezu
Izikulufu zokhuniIzikulufu zokhuni30 izicucu

Amathuluzi adingekayo:

Isaha SesandlaIsaha Sesandla
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Ama-clampAma-clamp
Iphepha LokugayaIphepha Lokugaya
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
Ithephu LokulinganisaIthephu Lokulinganisa
7

The parallel rest v v o o w

Cut two hardwood uprights o 30 x 13 x 190 mm and pin each to a side of the box with an 8 mm bolt 22 mm above the inside floor, 100 mm from the right end. Cut a pine division board w 228 x 170 mm and pin its foot to two hardwood blocks on the floor 200 mm from the left end, so it stands 16 mm clear of the floor. Cut two hardwood bars v 20 x 20 x 340 mm and pin them to the uprights' tops and w's top corners, 300 mm apart, with 160 mm between each foot and top pivot, so the bars stay level as the frame leans. Screw a hardwood handle h i 30 x 12 mm to the left end of one bar, long enough to stand 100 mm above the rim, and bend a flat-bar frame e over the rim to hold it with a pin through holes drilled every 20 mm in the handle.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Ipulangwe lomphayiniIpulangwe lomphayini1 ucezu
Izikulufu zomshiniIzikulufu zomshini8 izicucu
Inati Yokukhiya EnenayiloniInati Yokukhiya Enenayiloni8 izicucu
Iwasha EliyisicabaIwasha Eliyisicaba16 izicucu
Ibha Eyisicaba Yensimbi EthambileIbha Eyisicaba Yensimbi Ethambile1 ucezu
Izikulufu zokhuniIzikulufu zokhuni6 izicucu

Amathuluzi adingekayo:

Isaha SesandlaIsaha Sesandla
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isaha SensimbiIsaha Sensimbi
Isibambo SebhentshiIsibambo Sebhentshi
Izinsimbi zokuhlikihla (ezesandla)Izinsimbi zokuhlikihla (ezesandla)
Isipanela esilungisekayoIsipanela esilungisekayo
8

Chamber b and the fan

From pine make chamber b open below: two sides 360 x 270 mm, two ends 234 x 270 mm and a top 360 x 270 mm, 270 mm wide outside so it sits on the bars inside a. Drill both sides 12.5 mm for the fan shaft 40 mm up from b's lower edge and 230 mm from its left end, and one side again 170 mm above that for the crank shaft. Cut the 12 mm stainless rod to 285 mm for the fan. Push eight hardwood arms 18 x 18 x 69 mm into the hub's sockets, screw a bucket across each pair of arm ends, slide the hub onto the shaft inside b and fix it with an M4 screw across.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe lomphayiniIpulangwe lomphayini2 izicucu
Iglu LokhuniIglu Lokhuni1 ucezu
Izikulufu zokhuniIzikulufu zokhuni20 izicucu
Insimbi engagqwali eyindukwanaInsimbi engagqwali eyindukwana1 ucezu
Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Ifilamenti ye-PETGIfilamenti ye-PETG1 ucezu
Izikulufu zomshiniIzikulufu zomshini9 izicucu
Inati Yokukhiya EnenayiloniInati Yokukhiya Enenayiloni9 izicucu

Amathuluzi adingekayo:

Iphrinta ye-3D yentambo (i-FDM)Iphrinta ye-3D yentambo (i-FDM)
Isaha SesandlaIsaha Sesandla
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isaha SensimbiIsaha Sensimbi
Izinsimbi zokuhlikihla (ezesandla)Izinsimbi zokuhlikihla (ezesandla)
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
9

Pulleys f and c, crank t

Cut a pulley f 240 mm across and a pulley c 60 mm across from 12 mm plywood, each with a 3 mm flange glued on the outer face, and file a groove round each rim for the cord. Fix c on the fan shaft outside b. Run a 12 mm stainless stub shaft through b's side 170 mm above, fix f on it and a hardwood crank arm 24 x 10 x 112 mm with a 24 mm dowel handle 80 mm long beyond it, out over the side of a. Tie a loop of 6 mm cotton cord round both pulleys.

Izinto zokwakha zalesi sinyathelo:

Ishidi le-plywoodIshidi le-plywood1 ucezu
Iglu LokhuniIglu Lokhuni1 ucezu
Insimbi engagqwali eyindukwanaInsimbi engagqwali eyindukwana1 ucezu
Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu
Igoda lekotiniIgoda lekotini1 m
Izikulufu zomshiniIzikulufu zomshini2 izicucu
Inati Yokukhiya EnenayiloniInati Yokukhiya Enenayiloni2 izicucu

Amathuluzi adingekayo:

Isaha Le-jigsawIsaha Le-jigsaw
Izinsimbi zokuhlikihla (ezesandla)Izinsimbi zokuhlikihla (ezesandla)
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isaha SensimbiIsaha Sensimbi
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
10

The build in 3D

FreeCAD model of this build, the near side of both boxes cut away: box a, the uprights, division board and bars of the parallel rest leaning 50 degrees, chamber b on the bars, the fan with its buckets, pulleys f and c, the crank, and handle h i in its frame e. The cord is not drawn.
Ifayela LomklamoBLENDCC0 - Free
11

Churn

Pour in about 14 litres of heavy cream at about 15 °C, checked with the thermometer. Set chamber b on the bars and move the handle until the buckets just dip into the cream, about 3 mm, then pin it in frame e (the notebook gives the lean for other quantities). Turn the crank fast and time it: the fan throws cream over the division board and it returns under it. When the butter comes, lift b off, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Izinto zokwakha zalesi sinyathelo:

Ukhilimu ojiyileUkhilimu ojiyile14 l
Usawoti Wolwandle OmkhuluUsawoti Wolwandle Omkhulu1 ucezu
AmanziAmanzi1 ucezu

Amathuluzi adingekayo:

Ithemomitha enenaliti eshiywa ngaphakathiIthemomitha enenaliti eshiywa ngaphakathi
Iwashi Lokumisa IsikhathiIwashi Lokumisa Isikhathi
Isikali Sedijithali SasekhishiniIsikali Sedijithali Sasekhishini
Isitsha esikhulu sokuxuba sensimbi engagqwaliIsitsha esikhulu sokuxuba sensimbi engagqwali
12

Troubleshooting

Surface dash-wheel churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Andrew Patterson** of Birmingham, Allegheny County, Pennsylvania, US 23,111, 1 March 1859, "Churn". He held that a fast fan at the surface does more than a submerged wheel, which has to lift the whole cream, and that it also gathers the butter on the far side of the partition. He claimed box a with chamber b serving as its lid and as the frame for the dash wheel and crank. His only figure is the 1/8 in. dip; every size and material here is ours.

Izinto

16

Amathuluzi Adingekayo

17

Amafayela omklamo

3

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...