Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Rinsing-Ring Churn: Lid, Gearing, Dasher and Breaker Bars Lift Out as One, a Perforated Ring Under the Lid Washes Them
Buttercup

Yenziwe ngu-

Buttercup

11. uLwezi 2026IE
3
0
0
0
0

Rinsing-Ring Churn: Lid, Gearing, Dasher and Breaker Bars Lift Out as One, a Perforated Ring Under the Lid Washes Them

William W. Reid of Rochester, New York, received US 30,424, dated 16 October 1860, for a geared churn whose lid, gearing, two-slat dasher and four upright breaker bars are joined into one frame that lifts out of the body together. Under the lid runs a ring-shaped tube with small holes on both faces: water poured into a funnel on the lid sprays inward onto the dasher and outward onto the bars and wall, rinsing them, or tempering the cream, without lifting the lid. The patent's only size is the holes about an inch apart; every other size here is ours.
Ophakathi
About 2 days

Imiyalelo

1

The rinsing ring

Ilayisha incwadi ye-Jupyter…
2

A geared frame that sits on the churn, four months before

Evans sets his gearing on a frame over the churn. Reid joins gearing, dasher and breakers to the lid so all come out together.
3

Read US 30,424

"The tunnel t, fits into a short tube P, which passes through the lid B, and is inserted into the annular tube n, so that when water is poured into the tunnel t, it is projected in numerous small jets both inwardly upon the dasher and also outwardly against the upright bars I, I, I, I, and sides of the churn, and thus washes off the milk and small particles of butter."
4

Body and faucet C

Use a 20-litre food-grade bucket as the body. Bore a 21 mm hole 40 mm above its floor and fit a brass spigot C with its washers and nut. Screw two hardwood stop blocks 22 x 24 x 25 mm inside the rim, one above the spigot and one opposite, from outside through the wall, so the lid cannot turn.

Izinto zokwakha zalesi sinyathelo:

Ibhakede Lamalitha Angu-20Ibhakede Lamalitha Angu-201 ucezu
Umpompi wethusiUmpompi wethusi1 ucezu
Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Izikulufu zokhuniIzikulufu zokhuni4 izicucu

Amathuluzi adingekayo:

Isethi yezingqamuzana ezinjengefosholoIsethi yezingqamuzana ezinjengefosholo
Ibhola ElingenantamboIbhola Elingenantambo
Isipanela esilungisekayoIsipanela esilungisekayo
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
5

Print the ring tube n

The annular tube n: hollow, 16 x 16 mm in section with 2 mm walls, 196 mm across outside and 164 inside, with 23 holes of 2 mm on its inner face and 23 on its outer face, about an inch apart, and an inlet on top for the tube P. Needs a 200 mm bed. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Ifayela LomklamoSTLCC0 - Free
6

Lid B, ring n, tube P and funnel t

Cut a 12 mm HDPE lid B to the bucket's top, 304 mm across, bore it 16.6 mm at the centre as the shaft's top bearing, and cut two notches at its edge to drop over the stop blocks. Rout a groove 17 mm wide and 8 mm deep under it, 180 mm across its middle, and seal the ring tube n into it so half the ring stands below. Bore 12.2 mm through the lid over the ring's inlet, 90 mm out from the centre, and seal in a 12 mm stainless tube P 40 mm long standing 30 mm proud; set a small kitchen funnel t in it.

Izinto zokwakha zalesi sinyathelo:

Ishidi le-HDPEIshidi le-HDPE1 ucezu
Ifilamenti ye-PETGIfilamenti ye-PETG1 ucezu
Isivalo Se-siliconeIsivalo Se-silicone1 ucezu
Ishubhu lensimbi engagqwaliIshubhu lensimbi engagqwali1 ucezu
Isifaneli sasekhishiniIsifaneli sasekhishini1 ucezu

Amathuluzi adingekayo:

Iphrinta ye-3D yentambo (i-FDM)Iphrinta ye-3D yentambo (i-FDM)
IkhompasiIkhompasi
Isaha Le-jigsawIsaha Le-jigsaw
I-router yokhuniI-router yokhuni
Isethi yezingqamuzana ezinjengefosholoIsethi yezingqamuzana ezinjengefosholo
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isaha SensimbiIsaha Sensimbi
Izinsimbi zokuhlikihla (ezesandla)Izinsimbi zokuhlikihla (ezesandla)
7

Bars H and I, shaft S and dasher O

Halve two hardwood bars H 260 x 40 x 20 mm across each other and glue them; bore a 10.6 mm socket 20 mm deep at the middle. Screw four hardwood bars I 20 mm square and 351 mm long upright on their ends, 120 mm from the centre, and their tops to the lid's underside. Cut a hardwood shaft S 32 mm square and 325 mm long, set a 10 mm stainless pin 15 mm out of its foot and a 16 mm stainless rod 108 mm long 20 mm into its top. Screw two hardwood slats O 95 x 12 x 290 mm on opposite faces of S, reaching out opposite ways, 15 mm above its foot. Stand S in the socket and up through the lid's bearing.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile2 izicucu
Iglu LokhuniIglu Lokhuni1 ucezu
Izikulufu zokhuniIzikulufu zokhuni16 izicucu
Insimbi engagqwali eyindukwanaInsimbi engagqwali eyindukwana2 izicucu

Amathuluzi adingekayo:

Isaha letafulaIsaha letafula
Isethi yezisebenzi zokhuniIsethi yezisebenzi zokhuni
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isaha SensimbiIsaha Sensimbi
Isibambo sensikaIsibambo sensika
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
Ithephu LokulinganisaIthephu Lokulinganisa
8

Print the wheel f

The wheel f on the crank shaft: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Ifayela LomklamoSTLCC0 - Free
9

Print the pinion e

The pinion e on the top of S: 14 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Ifayela LomklamoSTLCC0 - Free
10

Supports d, wheel f, pinion e and crank A

Pin the pinion e on the rod of S with its teeth centred 40 mm above the lid. Screw two hardwood supports d 50 x 25 x 118 mm to the lid either side of it, one 60 to 85 mm in front and one 25 to 50 mm behind, bored 16.6 mm across 92 mm up. Run a 16 mm stainless crank shaft 180 mm long through them, pin the wheel f on it meshing e, hold it with a shaft collar, and pin on a crank A of mild steel flat bar, 100 mm throw, with a hardwood handle.

Izinto zokwakha zalesi sinyathelo:

Insimbi engagqwali eyindukwanaInsimbi engagqwali eyindukwana1 ucezu
Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Shaft CollarShaft Collar1 ucezu
Iphini elinemilenze emibiliIphini elinemilenze emibili3 izicucu
Ibha Eyisicaba Yensimbi EthambileIbha Eyisicaba Yensimbi Ethambile1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu
Izikulufu zokhuniIzikulufu zokhuni4 izicucu
Ifilamenti ye-PETGIfilamenti ye-PETG1 ucezu

Amathuluzi adingekayo:

Iphrinta ye-3D yentambo (i-FDM)Iphrinta ye-3D yentambo (i-FDM)
Isaha letafulaIsaha letafula
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isaha SensimbiIsaha Sensimbi
Izinsimbi zokuhlikihla (ezesandla)Izinsimbi zokuhlikihla (ezesandla)
Isibambo SebhentshiIsibambo Sebhentshi
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
11

The build in 3D

FreeCAD model of this build, the bucket and lid cut open: the crossed bars and four upright bars, the shaft with its two slats, the ring tube under the lid with its holes, the tube and funnel, the spigot and stop blocks, and the gearing and crank on the lid.
Ifayela LomklamoBLENDCC0 - Free
12

Churn and rinse

Pour about 12 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket and lower the whole frame in, the lid's notches over the stop blocks. Turn the crank steadily, timing it; to warm or cool the cream, pour a little warm or cold water into the funnel. When the butter comes, draw the buttermilk off at the spigot into a bowl, then pour cold water into the funnel to rinse the dasher, bars and walls, turning slowly, and draw it off. Lift the frame out, take out the butter, wash it in cold water until it runs clear, salt and weigh it.

Izinto zokwakha zalesi sinyathelo:

Ukhilimu ojiyileUkhilimu ojiyile12 l
AmanziAmanzi1 ucezu
Usawoti Wolwandle OmkhuluUsawoti Wolwandle Omkhulu1 ucezu

Amathuluzi adingekayo:

Ithemomitha enenaliti eshiywa ngaphakathiIthemomitha enenaliti eshiywa ngaphakathi
Iwashi Lokumisa IsikhathiIwashi Lokumisa Isikhathi
Isikali Sedijithali SasekhishiniIsikali Sedijithali Sasekhishini
Isitsha esikhulu sokuxuba sensimbi engagqwaliIsitsha esikhulu sokuxuba sensimbi engagqwali
13

Troubleshooting

Rinsing-ring churn troubleshooting.

Flow

Loading...
14

History and honest limits

**William W. Reid** of Rochester, Monroe County, New York, US 30,424, 16 October 1860, "Churn". He claimed "the annular perforated tube n in combination with the bars I I and dasher O". His tube was rectangular tin; ours is printed. His wheel and pinion were bevel gears on cast supports; ours are a printed crown wheel and pinion on wooden supports. The holes about an inch apart are his; every other size here is ours.

Izinto

18

Amathuluzi Adingekayo

20

Amafayela omklamo

4

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...