Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Slatted-Wing Concave-Hub Churn: Flanged Wings Lift the Butter, a Hollow-Sided Hub Rolls It Up
English
Hoop

Yenziwe ngu-

Hoop

8. uMfumfu 2026GB
39
0
0
0
0

Slatted-Wing Concave-Hub Churn: Flanged Wings Lift the Butter, a Hollow-Sided Hub Rolls It Up

William Brown of Duncannon, Pennsylvania, received US 20,189, dated 11 May 1858, for a revolving churn dasher: four wings of slats that let the cream through, flanges across their ends that hold the butter, and a solid hub with concave sides into which the butter falls and rolls together. This rung prints the hub and wings at tabletop scale and turns them on a dowel in a storage container.
Ophakathi
About 4 hours, plus printing

Imiyalelo

1

Slats and gaps

Ilayisha incwadi ye-Jupyter…
2

Box churns with a turning dasher, before it

Porter turned float boards on crossed arms; Brown slats the wings, flanges their ends and hollows the hub.
3

Read US 20,189

"As fast as the butter is produced the flanges collect and retain it upon the slatted wings until the wings arise out of the cream and assume a position which compels it to fall into the concaves of the solid hub."
4

Print the parts

Print the hub standing on end, four wings flat with the flange up, two end caps, the crank and the collar. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.

Izinto zokwakha zalesi sinyathelo:

Ifilamenti ye-PETGIfilamenti ye-PETG1 ucezu

Amathuluzi adingekayo:

Iphrinta ye-3D yentambo (i-FDM)Iphrinta ye-3D yentambo (i-FDM)
5

Print the hub

The hub, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
6

Print the wing

The wing, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
7

Print the end cap

The end cap, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
8

Print the crank

The crank, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
9

Print the collar

The collar, printed as step 4 describes.
Ifayela LomklamoSTLCC0 - Free
10

Container and axle

Use a container at least 230 mm long, 180 mm wide and 200 mm deep inside. Drill a 10.5 mm hole in the middle of each end wall, 100 mm above the inside floor. Cut a 10 mm dowel 310 mm long as the axle and sand it.

Izinto zokwakha zalesi sinyathelo:

Isitsha sokugcina sezinga lokudlaIsitsha sokugcina sezinga lokudla1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu

Amathuluzi adingekayo:

Ibhola ElingenantamboIbhola Elingenantambo
Isaha SesandlaIsaha Sesandla
Iphepha LokugayaIphepha Lokugaya
11

Assemble the dasher

Slide the four wings into the hub's slots, every flange facing the same way round. Screw an end cap on each end with four M3 screws. Push the axle through one end wall, the hub and the other wall. Drill 2.5 mm through the axle at the hub's cross hole and fix it with an M3 screw; fit the crank on one end and the collar on the other the same way.

Izinto zokwakha zalesi sinyathelo:

Izikulufu zomshiniIzikulufu zomshini1 ucezu

Amathuluzi adingekayo:

Ibhola ElingenantamboIbhola Elingenantambo
Isethi yezikulufudrayivaIsethi yezikulufudrayiva
12

The build in 3D

FreeCAD model of this build: the container cut open, the hub with four concave sides, four slatted wings in its dovetails with their flanges all one way, the end caps, the dowel axle, the crank and the collar.
Ifayela LomklamoBLENDCC0 - Free
13

Churn and roll

Pour in 2 litres of heavy cream at about 15 °C, checked with the thermometer. Turn the crank so the flanges lead, and time it with the stopwatch. Keep turning once the butter comes: the flanges lift it out of the cream and drop it into the hub's concaves, where it gathers into a roll. Lift the dasher out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Izinto zokwakha zalesi sinyathelo:

Ukhilimu ojiyileUkhilimu ojiyile2 l
Usawoti Wolwandle OmkhuluUsawoti Wolwandle Omkhulu1 ucezu
AmanziAmanzi1 ucezu

Amathuluzi adingekayo:

Ithemomitha enenaliti eshiywa ngaphakathiIthemomitha enenaliti eshiywa ngaphakathi
Iwashi Lokumisa IsikhathiIwashi Lokumisa Isikhathi
Isikali Sedijithali SasekhishiniIsikali Sedijithali Sasekhishini
Isitsha esikhulu sokuxuba sensimbi engagqwaliIsitsha esikhulu sokuxuba sensimbi engagqwali
14

Troubleshooting

Slatted-wing churn troubleshooting.

Flow

Loading...
15

History and honest limits

**William Brown** of Duncannon, Perry County, Pennsylvania, US 20,189, 11 May 1858, signed 13 April 1858. He hung the dasher in the churn box "in the usual manner" and claimed the slatted wings, the flanges and the solid concaved hub in combination. He wrote that slats parallel with the hub would do in a measure, but set them at right angles so the butter rolls to the centre with less obstruction. Our container, sizes, dovetails and printed parts are ours. FDM prints hold food in their layer lines, so wash well and replace when worn.

Izinto

7

Amathuluzi Adingekayo

9

Amafayela omklamo

6

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...