Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Alcohol Burner: the Glass Spirit Lamp with a Copper Wick Shield (Morfit, 1849)
Charlie

Yenziwe ngu-

Charlie

7. uLwezi 2026DE
3
0
0
0
0

Alcohol Burner: the Glass Spirit Lamp with a Copper Wick Shield (Morfit, 1849)

A small glass lamp that burns alcohol for heating test tubes and small vessels on the bench. Campbell Morfit (1849): the glass body holds the alcohol; a round copper shield with a tube in its centre carries a cotton wick and rests on the neck; a minute hole in the shield lets vapour escape; a glass cap ground to fit the neck keeps the alcohol from evaporating. Alcohol gives no smoke and does not blacken the glass. Sizes, and how the wick tube is fixed, are not given. Source: C. Morfit, Chemical and Pharmaceutic Manipulations (1849), pp. 160-162. Picture: Fig. 115.
Oqalayo
Unknown

Imiyalelo

1

Read Morfit

"To the neck b is adjusted a copper circular shield c, with a tube in its centre for the passage of the wick, which should be of cotton, and similar to that used for tallow candles. The shield should rest upon, rather than within the neck, otherwise its expansion by the heat may cause the breakage of the glass. A minute opening drilled in the shield is also requisite for the escape of vapor in case the alcohol should become heated."
2

Make the copper shield

Cut a round copper shield a little wider than the neck of the glass body, so it rests on the neck and not inside it. Fix a short copper tube through its centre for the wick (ours: soldered; the joint is not given). Drill a minute hole in the shield for vapour to escape. Sizes are not given (unknown).

Izinto zokwakha zalesi sinyathelo:

Ishidi LethusiIshidi Lethusi1 shield
Ishubhu lethusiIshubhu lethusi1 wick tube
I-solder ye-tin nomthofuI-solder ye-tin nomthofu1 joint
IfulaksiIfulaksi1 joint

Amathuluzi adingekayo:

Isikeli sensimbiIsikeli sensimbi
Insimbi yokushiselaInsimbi yokushisela
Ibhola lesandlaIbhola lesandla
Izilinganiso ezingaziwaIzilinganiso ezingaziwa
3

Fit the wick and the body

Draw a cotton wick of the tallow-candle kind through the tube so it reaches down into the glass body, which is the alcohol reservoir. Set the shield on the neck. Ours: a clear glass bottle as the body.

Izinto zokwakha zalesi sinyathelo:

Ibhodlela lengilazi (elicwebile)Ibhodlela lengilazi (elicwebile)1 body
Intambo yekhandlela kakotiniIntambo yekhandlela kakotini1 ucezu

Amathuluzi adingekayo:

Isikeli sensimbiIsikeli sensimbi
4

Fit the glass cap

Cover the wick, when the lamp is not in use, with a glass cap ground inside to fit the neck closely. It stops the alcohol evaporating and the wick taking up water, which makes relighting difficult. Put it on only after the lamp is out. How the cap is made and ground is not given (unknown).

Izinto zokwakha zalesi sinyathelo:

Ingilazi engaziwaIngilazi engaziwa1 cap

Amathuluzi adingekayo:

Izilinganiso ezingaziwaIzilinganiso ezingaziwa
5

Fill and use

Morfit burns alcohol of about specific gravity 0.85. Always put the lamp out before refilling, then pour the spirit in gently until the reservoir is nearly full. The flame is hottest just below its tip; bring the vessel to it gradually, and spread the heat with copper gauze between flame and vessel for larger surfaces.

Izinto

7

Amathuluzi Adingekayo

4

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...