Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Washing Machine with Churn: One Crank Pounds the Wash, Turns the Tub and Works a Dash Churn (Wagoner & Severson, 1859)
YourGrandma

Yenziwe ngu-

YourGrandma

11. uLwezi 2026IS
6
0
0
0
0

Washing Machine with Churn: One Crank Pounds the Wash, Turns the Tub and Works a Dash Churn (Wagoner & Severson, 1859)

John Wagoner and Abram Severson Jr. of Guilderland Center, New York, received US 25,152, dated 16 August 1859, for a washing machine. A crank shaft with a heavy balance wheel rocks a long lever. A springy beam on the lever carries a pounder into the tub, and a belt and a pair of bevel wheels turn the tub slowly under it. The tub stands on a hinged platform: folded up it slackens the belt, and let down the tub's weight tightens it. A pin on the lever also works the dash of a churn standing beside the machine, with or without the washing. The patent gives no sizes; every size here is ours.
Osezingeni eliphezulu
About 5 days, plus printing

Imiyalelo

1

Crank pin, strokes and tub speed

Ilayisha incwadi ye-Jupyter…
2

One crank working a churn and a washtub, a year before

Swan's machine lifted a plunger by a cam. Here a springy beam carries the pounder, and the tub's own weight tightens the belt that turns it.
3

Read US 25,152

"In addition to what has now been described our machine is adapted to operate a churn very effectively either alone or simultaneously with the washing operation." "We place the center of our tube J out of the plane of the motion of the levers T and V. Our pounder therefore inclines to strike on one side of J and not in the center thereby increasing the uniformity of the effect on the contents."
4

Print the pulley for shaft D

Flat-faced pulley 120 mm across and 40 mm wide, bored 31 mm for shaft D. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Ifayela LomklamoSTLCC0 - Free
5

Print pulley R

Flat-faced pulley 100 mm across and 40 mm wide, bored 21 mm for the lower bevel wheel's shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Ifayela LomklamoSTLCC0 - Free
6

Frame A, legs B and uprights C

From 70 x 70 mm timber cut three stringers 1500 mm, two cross pieces 630 mm, four legs 700 mm, an upright 830 mm and an upright 720 mm. Bolt the cross pieces across the tops of the legs and the stringers on the cross pieces, 210 mm apart, so the frame's top is 840 mm from the floor. Bolt the long upright to the outside of the front stringer 100 mm from the left end and the short one 100 mm from the right end. Chisel an opening 50 x 260 mm through the left upright, from 440 to 700 mm above the stringer, and bore it across 560 mm up for pin v (a 16 mm bolt).

Izinto zokwakha zalesi sinyathelo:

Ukhuni oluthambile lwe-70x70 mmUkhuni oluthambile lwe-70x70 mm11 m
Ibhawoti elinekhanda eliyindilingaIbhawoti elinekhanda eliyindilinga16 izicucu
Iwasha EliyisicabaIwasha Eliyisicaba16 izicucu
Inati Yokukhiya EnenayiloniInati Yokukhiya Enenayiloni16 izicucu

Amathuluzi adingekayo:

Isaha SesandlaIsaha Sesandla
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isethi yezingqamuzana ezinjengefosholoIsethi yezingqamuzana ezinjengefosholo
Isisebenziso sokuqopha imboboIsisebenziso sokuqopha imbobo
Isando SokhuniIsando Sokhuni
Isikwele esiqinileIsikwele esiqinile
Ithephu LokulinganisaIthephu Lokulinganisa
Isipanela esilungisekayoIsipanela esilungisekayo
Isibambo sensikaIsibambo sensika
7

Shaft D, balance wheel F and crank E

Bolt three bearing blocks on the stringers' tops 650 mm from the left end and pass a 30 mm steel shaft D through them, 710 mm long. Build the balance wheel from three layers of 20 mm hardwood segments glued crossways: 840 mm across, a 100 mm rim and four spokes, 50 mm thick in all. Fit it on D between the front and middle stringers, the printed pulley between the middle and back stringers, and a hand crank 240 mm long on the back end. On the front end fit crank E, a hardwood arm 20 mm thick with a slot from 50 to 125 mm out, and a 20 mm bolt in the slot for the crank pin e.

Izinto zokwakha zalesi sinyathelo:

Insimbi engagqwali eyindukwanaInsimbi engagqwali eyindukwana1 ucezu
Ibhulokhi yebhereIbhulokhi yebhere3 izicucu
Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile3 izicucu
Iglu LokhuniIglu Lokhuni1 ucezu
Iqoqo lamabhawoti anezinhlangothi eziyisithuphaIqoqo lamabhawoti anezinhlangothi eziyisithupha13 izicucu
Inati Yokukhiya EnenayiloniInati Yokukhiya Enenayiloni13 izicucu
Shaft CollarShaft Collar2 izicucu

Amathuluzi adingekayo:

Isaha Le-jigsawIsaha Le-jigsaw
IkhompasiIkhompasi
Isaha letafulaIsaha letafula
Ibhola ElingenantamboIbhola Elingenantambo
Isethi yezingqamuzana ezinjengefosholoIsethi yezingqamuzana ezinjengefosholo
I-router yokhuniI-router yokhuni
Isibambo sensikaIsibambo sensika
Isaha SensimbiIsaha Sensimbi
Isipanela esilungisekayoIsipanela esilungisekayo
8

Lever T, link U and rod V

Cut lever T from hardwood 40 x 70 mm, 1195 mm long. Bolt it to the front of the right upright, 610 mm above the stringer, free to rock. Join it to the crank pin by link U, hardwood 20 x 40 mm with its pin holes 560 mm apart, 715 mm from T's pivot. At T's left end join rod V, hardwood 30 x 40 mm, slotted 22 mm wide for 220 mm, and pass it through the left upright's opening astride pin v. Fix a steel pin 3, 24 mm and 370 mm long, through T 1015 mm from its pivot, sticking out at the front for the churn.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile2 izicucu
Iqoqo lamabhawoti anezinhlangothi eziyisithuphaIqoqo lamabhawoti anezinhlangothi eziyisithupha4 izicucu
Iwasha EliyisicabaIwasha Eliyisicaba8 izicucu
Inati Yokukhiya EnenayiloniInati Yokukhiya Enenayiloni4 izicucu
Insimbi engagqwali eyindukwanaInsimbi engagqwali eyindukwana1 ucezu

Amathuluzi adingekayo:

Isaha letafulaIsaha letafula
I-router yokhuniI-router yokhuni
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isethi yezingqamuzana ezinjengefosholoIsethi yezingqamuzana ezinjengefosholo
Isaha SensimbiIsaha Sensimbi
Iphepha LokugayaIphepha Lokugaya
Isipanela esilungisekayoIsipanela esilungisekayo
Ithephu LokulinganisaIthephu Lokulinganisa
9

Spring beam W and the pounder

Cut the spring beam W from ash 30 x 40 mm, 1210 mm long. Lay it on T's top, its left end against a block glued on T, bolt it through T 415 mm left of the pivot with a wing nut (the hand nut w), and let it run past the upright to overhang the frame by 510 mm. Make rod X from hardwood 40 x 40 mm, 1090 mm long, with four holes at its top for height. Under it glue a hardwood head 200 x 120 mm with five legs 30 x 36 mm, 160 mm long, each slotted (Z) and bored across (z). Hang X from W's end on a bolt so it swings freely, in front of W.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe le-ashIpulangwe le-ash1 ucezu
Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Iglu LokhuniIglu Lokhuni1 ucezu
Iqoqo lamabhawoti anezinhlangothi eziyisithuphaIqoqo lamabhawoti anezinhlangothi eziyisithupha2 izicucu
Inathi yamaphikoInathi yamaphiko1 ucezu
Iwasha EliyisicabaIwasha Eliyisicaba4 izicucu

Amathuluzi adingekayo:

Isaha letafulaIsaha letafula
I-router yokhuniI-router yokhuni
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isisebenziso sokuqopha imboboIsisebenziso sokuqopha imbobo
Isando SokhuniIsando Sokhuni
Iphepha LokugayaIphepha Lokugaya
Isibambo sensikaIsibambo sensika
10

Hinged platform M, bevel wheels and platform K

Make platform M from 40 mm hardwood, 860 x 860 mm, and hang it on two strap hinges (the butts m) at the feet of the right-hand legs. On M, 100 mm from the hinges, fit a 20 mm vertical shaft in a flange bearing with pulley R and the lower bevel wheel on it. In a hardwood post fit a 20 mm cross shaft with the upper bevel wheel and a 240 mm hardwood pulley P in line with the pulley on D. 480 mm from the hinges, 340 mm towards the front, set a 24 mm shaft L in a hardwood block that slides in a slot along M, with a compression spring pushing it away from R. Glue platform K, 660 mm across and 40 mm thick, bore it for L, and set four 40 mm hardwood wheels l under its edge.

Izinto zokwakha zalesi sinyathelo:

Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile4 izicucu
Iglu LokhuniIglu Lokhuni1 ucezu
Ihinji lolutho lwensimbiIhinji lolutho lwensimbi2 izicucu
Ibhering elinefulenjiIbhering elinefulenji3 izicucu
Isethi yamagiya e-bevel (insimbi, 1:1)Isethi yamagiya e-bevel (insimbi, 1:1)1 ucezu
Insimbi engagqwali eyindukwanaInsimbi engagqwali eyindukwana1 ucezu
Shaft CollarShaft Collar3 izicucu
Iqoqo lezintambo zokucindezelaIqoqo lezintambo zokucindezela1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu
Izikulufu zokhuniIzikulufu zokhuni40 izicucu
Iqoqo lamabhawoti anezinhlangothi eziyisithuphaIqoqo lamabhawoti anezinhlangothi eziyisithupha4 izicucu
Inati Yokukhiya EnenayiloniInati Yokukhiya Enenayiloni4 izicucu
Ifilamenti ye-PETGIfilamenti ye-PETG1 ucezu

Amathuluzi adingekayo:

Iphrinta ye-3D yentambo (i-FDM)Iphrinta ye-3D yentambo (i-FDM)
Isaha Le-jigsawIsaha Le-jigsaw
IkhompasiIkhompasi
I-router yokhuniI-router yokhuni
Ibhola ElingenantamboIbhola Elingenantambo
Iqoqo Lamakhanda EbholaIqoqo Lamakhanda Ebhola
Isethi yezingqamuzana ezinjengefosholoIsethi yezingqamuzana ezinjengefosholo
Isaha SensimbiIsaha Sensimbi
Isibambo sensikaIsibambo sensika
Isipanela esilungisekayoIsipanela esilungisekayo
11

Belts O and S, and the fold

Put belt S round pulley R and platform K's rim. Fold M up against the frame, run a string round the pulley on D and pulley P, and choose belt O just short enough that, with M let down and empty, it holds M at a slight angle; "The belt O is sufficiently short to hold the platform M at a slight angle until the weight of J is added thereto." Set the wooden tub J on K: its weight should pull M flat and the belt tight. Oil the wood.

Izinto zokwakha zalesi sinyathelo:

Ibhande lokushayelaIbhande lokushayela2 izicucu
Ubhavu wokhuniUbhavu wokhuni1 ucezu
Uwoyela We-linseed ObilisiweUwoyela We-linseed Obilisiwe1 ucezu

Amathuluzi adingekayo:

Ithephu LokulinganisaIthephu Lokulinganisa
12

The build in 3D

FreeCAD model of this build: the frame, shaft D with the balance wheel and crank E, lever T with link U and rod V, the spring beam W and the pounder in the tub (front of the tub cut away), the hinged platform M with the bevel wheels, pulleys and belts, and the churn on pin 3. The crank was turned through 18 positions.
Ifayela LomklamoBLENDCC0 - Free
13

Wash

Put warm water, soap and the clothes in the tub, and set the pounder's height so its feet clear the tub's bottom by the clothes. Turn the hand crank steadily. The pounder rises and falls on one side of the tub while the tub turns under it, so every part of the wash comes under it in turn. Move the crank pin out in its slot for a longer stroke, in for a shorter one. Lift the clothes out to rinse and wring.

Amathuluzi adingekayo:

AmanziAmanzi
Insipho eyisigaxaInsipho eyisigaxa
14

Churn on pin 3

Make the dash 2: a hardwood rod 35 mm across, 1250 mm long, bored at the top to hang on pin 3, with two crossed blades 220 x 30 x 20 mm at the bottom. Stand the churn under pin 3, beside the machine, pour in about 10 litres of cream at about 15 °C (checked with the thermometer), a third of its height, pass the dash through the lid and hang it on pin 3. Turn the crank, with or without the wash, timing it. When the butter comes, lift the dash off the pin, drain the buttermilk, wash the butter in cold water, salt and weigh it.

Izinto zokwakha zalesi sinyathelo:

Ukhilimu ojiyileUkhilimu ojiyile10 l
Usawoti Wolwandle OmkhuluUsawoti Wolwandle Omkhulu1 ucezu
Ipulangwe Lokhuni OluqinileIpulangwe Lokhuni Oluqinile1 ucezu
Izikhonkwane zokhuni oluqinileIzikhonkwane zokhuni oluqinile1 ucezu

Amathuluzi adingekayo:

Isitsha sokuphehla ibhotelaIsitsha sokuphehla ibhotela
Ithemomitha enenaliti eshiywa ngaphakathiIthemomitha enenaliti eshiywa ngaphakathi
Iwashi Lokumisa IsikhathiIwashi Lokumisa Isikhathi
Isikali Sedijithali SasekhishiniIsikali Sedijithali Sasekhishini
Isitsha esikhulu sokuxuba sensimbi engagqwaliIsitsha esikhulu sokuxuba sensimbi engagqwali
AmanziAmanzi
Ibhola ElingenantamboIbhola Elingenantambo
Isethi yezingqamuzana ezinjengefosholoIsethi yezingqamuzana ezinjengefosholo
Isaha SesandlaIsaha Sesandla
15

Troubleshooting

Washing machine troubleshooting.

Flow

Loading...
16

History and honest limits

**John Wagoner and Abram Severson, Jr.** of Guilderland Center, New York, US 25,152, 16 August 1859, "Washing-Machine". They claimed mounting the platform K and the pulleys and gearing P Q R on the hinged platform M, so turning M up slackens belt O and turning it down lets the tub's weight tighten it. The patent gives no sizes; every size here is ours. Their hand lever H and rod I, a second way to turn D, are not built: we turn D by a crank, which the patent allows. The spring that urges K's centre against belt S is "not represented" in their drawing; ours is a compression spring in a slot.

Izinto

24

Amathuluzi Adingekayo

24

Amafayela omklamo

3

CC0 Isizinda Somphakathi

Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.

Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

Ingxoxo

(0)

Ngena ukuze ujoyine ingxoxo

Kulayishwa amazwana...