সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য

Sliding-Head Churn Drive: The Churn Rides on the Pulley Head and Stays in Line When the Belt Is Slacked
Joseph Forsyth of Wheeling, Virginia, received US 22,022, dated 9 November 1858, for working a churn by power from a big belt wheel. The pulley head slides along a guide block to tighten or slack the belt, which starts or stops the churn. The churn stands on a carriage fixed to the head, so its shaft stays in line with the pulley's. A platform on four screws raises or lowers different churns to the pulley's height.
This rung builds it full size with a hand-cranked wheel and a rope belt.
মধ্যবর্তী
About 2 days
নির্দেশাবলি
1
1
Speed, rope and slack
Speed, rope and slack
Jupyter নোটবুক লোড হচ্ছে…
2
2
Churns worked by power, before it
Churns worked by power, before it
Brush worked a dasher from a dog's tread-wheel. Forsyth turns a crank churn by a belt and stops it by slacking the belt.
3
3
Read US 22,022
Read US 22,022
"The nature of my invention consists, first, in combining the carriage D with the movable pulley head H H in such a manner that the said carriage will move with the head when it is required to stop or start the motion of the churn, thereby enabling me to keep the shafts of the pulley, and churn in line."
4
4
Wheel A and posts B
Wheel A and posts B
Cut a plywood disc 1160 mm across and two discs 1200 mm across from 18 mm plywood. Glue and screw a larger disc to each face of the smaller one: the gap between them is the rope groove C. Screw a 160 mm hub block on each side. Stand two 70 mm posts 730 mm tall on 900 mm sills, 150 mm apart, each with two braces. Bolt a flange bearing on each post's outer face, 700 mm up, and run a 30 mm shaft M through bearings, posts and wheel, cross-bolted to the hub.
এই ধাপের উপকরণ:
প্লাইউডের পাত3 টুকরা
কাঠের আঠা1 টুকরা
কাঠের স্ক্রু #8 × ১"60 টুকরা
নরম কাঠ ৭০x৭০ মিমি4 টুকরা
কাঠের স্ক্রু #10 x 3"24 টুকরা
ফ্ল্যাঞ্জ বিয়ারিং2 টুকরা
ইস্পাতের শ্যাফট ৩০ মিমি1 টুকরা
ষড়ভুজ বোল্টের সেট M105 টুকরাপ্রয়োজনীয় সরঞ্জাম:
জিগস করাত
হাত-করাত
তারবিহীন তুরপুন
ড্রিল-বিট সেট
কোদাল-বিট সেট
ক্ল্যাম্প
সমন্বয়যোগ্য রেঞ্চ
জলের সমতা মাপক
ফিতা-মাপ5
5
Crank
Crank
How the wheel is turned is not given; ours has a crank. Bolt a hardwood arm 350 x 70 x 30 mm on shaft M outside one bearing and glue a 30 mm dowel 150 mm long into it 280 mm from the shaft as the handle.
এই ধাপের উপকরণ:
শক্ত কাঠের তক্তা1 টুকরা
শক্ত কাঠের গোঁজ1 টুকরা
কাঠের আঠা1 টুকরা
ষড়ভুজ বোল্টের সেট M101 টুকরাপ্রয়োজনীয় সরঞ্জাম:
হাত-করাত
তারবিহীন তুরপুন
কোদাল-বিট সেট
শিরিষ কাগজ
সমন্বয়যোগ্য রেঞ্চ6
6
Guide block and pulley head
Guide block and pulley head
Screw a 900 mm guide block U of 70 mm timber to the floor in line with the wheel, 1300 mm from shaft M. Lay a 400 mm head block on it. Cut two frames H from 50 x 8 mm flat bar, 420 mm long, and bolt them to the head block's sides so their ends run down the guide block's sides. Bolt a flange bearing on each frame's outer face 400 mm up. Make the pulley O like the wheel: a 200 mm disc between two 240 mm rings. Fit it on a 30 mm shaft through the bearings.
এই ধাপের উপকরণ:
নরম কাঠ ৭০x৭০ মিমি2 টুকরা
কাঠের স্ক্রু #10 x 3"8 টুকরা
নরম ইস্পাতের চ্যাপ্টা পাটা2 টুকরা
ষড়ভুজ বোল্টের সেট M104 টুকরা
ফ্ল্যাঞ্জ বিয়ারিং2 টুকরা
ইস্পাতের শ্যাফট ৩০ মিমি1 টুকরা
প্লাইউডের পাত1 টুকরা
কাঠের আঠা1 টুকরা
কাঠের স্ক্রু #8 × ১"12 টুকরাপ্রয়োজনীয় সরঞ্জাম:
হ্যাকস
রেতি (হাতের রেতি)
বেঞ্চ ভাইস
তারবিহীন তুরপুন
ড্রিল-বিট সেট
জিগস করাত
সমন্বয়যোগ্য রেঞ্চ7
7
Strap F and thumb screw E
Strap F and thumb screw E
Bend a 30 x 5 mm flat bar into a bridge over the head block, 80 mm from the frames, and screw its legs to the guide block's sides. Drill its top for an M8 rod, run a nut onto the rod under the strap, and lock a wing nut on top as the thumb screw. Turn it down to clamp the head block.
এই ধাপের উপকরণ:
নরম ইস্পাতের চ্যাপ্টা পাটা1 টুকরা
কাঠের স্ক্রু #8 × ১"4 টুকরা
প্যাঁচকাটা দণ্ড1 টুকরা
ষড়ভুজ বাদাম2 টুকরা
প্রজাপতি নাট1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
বেঞ্চ ভাইস
হ্যাকস
তারবিহীন তুরপুন
ড্রিল-বিট সেট8
8
Carriage D and platform K
Carriage D and platform K
Bolt two 70 mm side bars, 865 mm long, to the head block's side, 330 mm apart, and join their far ends with a cross tie with a caster under its middle as the roller. Drill each bar twice for M12 rods (screws I), 360 mm apart; fix each rod with a nut above and below the bar. Run a nut down each rod, lay an 18 mm plywood platform 430 x 440 mm on them, and lock it with a second nut on top.
এই ধাপের উপকরণ:
নরম কাঠ ৭০x৭০ মিমি2 টুকরা
ষড়ভুজ বোল্টের সেট M104 টুকরা
ঘূর্ণায়মান চাকার সেট1 টুকরা
প্যাঁচকাটা দণ্ড4 টুকরা
ষড়ভুজ বাদাম16 টুকরা
সমতল ওয়াশার8 টুকরা
প্লাইউডের পাত1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
হাত-করাত
তারবিহীন তুরপুন
ড্রিল-বিট সেট
সমন্বয়যোগ্য রেঞ্চ
জলের সমতা মাপক9
9
Arm X and the rope belt
Arm X and the rope belt
Bolt a 140 mm flat-bar arm X with a 20 mm slot to a collar on the pulley shaft's end. Stand a crank churn on the platform and raise or lower the platform's nuts until its crank shaft is level with the pulley shaft and its handle V sits in the slot. Splice 12 mm cotton rope into a loop about 5 m long round both grooves (see the notebook), with the head slid towards the wheel.
এই ধাপের উপকরণ:
নরম ইস্পাতের চ্যাপ্টা পাটা1 টুকরা
ষড়ভুজ বোল্টের সেট M101 টুকরা
নাইলন-ভরা লক নাট1 টুকরা
সুতির রশি6 mপ্রয়োজনীয় সরঞ্জাম:
হ্যাকস
রেতি (হাতের রেতি)
তারবিহীন তুরপুন
ড্রিল-বিট সেট
সমন্বয়যোগ্য রেঞ্চ
ফিতা-মাপ10
10
The build in 3D
The build in 3D
FreeCAD model of this build: the wheel on its posts with the crank, the guide block, pulley head, strap and thumb screw, the carriage with its caster, platform K on its four screws, a stand-in churn and arm X. The rope is not drawn.
11
11
Churn
Churn
Pour about 10 litres of heavy cream at about 15 °C into the churn. Slide the head away from the wheel until the rope is tight and clamp it with the thumb screw. Turn the wheel steadily, about 10 times a minute, and time it. To stop, loosen the thumb screw and slide the head towards the wheel: the carriage and churn move with it. When the butter comes, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
এই ধাপের উপকরণ:
ঘন ক্রিম10 l
মোটা সমুদ্র লবণ1 টুকরা
জল1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
মাখন মন্থন পাত্র
ভিতরে রেখে দেওয়া প্রোব থার্মোমিটার
স্টপওয়াচ
ডিজিটাল রান্নাঘরের দাঁড়িপাল্লা
স্টেনলেস স্টিলের বড় মেশানোর বাটি12
12
Troubleshooting
Troubleshooting
Churn drive troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Joseph Forsyth** of Wheeling, Ohio County, Virginia (now West Virginia), US 22,022, 9 November 1858, "Operating Churns". He claimed the carriage D combined with the movable platform K. He gave no sizes, named only the "metallic" frames H, and did not say what turns wheel A or what the belt is: our hand crank, plywood wheel and pulley, cotton rope, timber, bearings, rods and caster are ours.
উপকরণ
21- 3 টুকরাপ্লেসহোল্ডার
- 3 টুকরাপ্লেসহোল্ডার
- 76 টুকরাপ্লেসহোল্ডার
- 4 টুকরাপ্লেসহোল্ডার
- 32 টুকরাপ্লেসহোল্ডার
- 2 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 15 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 2 টুকরাপ্লেসহোল্ডার
- 4 টুকরাপ্লেসহোল্ডার
- 18 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 8 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 6 mপ্লেসহোল্ডার
- 10 lপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
প্রয়োজনীয় সরঞ্জাম
18- 1 vendor sell this, none ship to you yetপ্লেসহোল্ডার
- প্লেসহোল্ডার
- 1 vendor sell this, none ship to you yetপ্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- 1 vendor sell this, none ship to you yetপ্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
ডিজাইন ফাইল
1এই ব্লুপ্রিন্ট যা তৈরি করে
সম্পর্কিত ব্লুপ্রিন্ট
এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি
CC0 পাবলিক ডোমেন
এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।
মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।



