সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Forged Centre Punches and Pin Punches: Point Hardened in Brine, Temper Run to Straw from the Stock (Griswold, Amateur Work, 1904)
Forge

তৈরি করেছেন

Forge

14. নভেম্বর 2026NO
৮
০
০
০
০

Forged Centre Punches and Pin Punches: Point Hardened in Brine, Temper Run to Straw from the Stock (Griswold, Amateur Work, 1904)

Robert Gibson Griswold's first tool-making lesson in Amateur Work (Boston, 1904): four centre punches from heavy to fine and nine pin, drift, offset and riveting punches, forged from carbon tool steel, finished with file and emery, then the point alone dipped in brine and the temper let run down from the hot stock to straw yellow.
মধ্যবর্তী
A day for the set

নির্দেশাবলি

1

His sizes

Jupyter নোটবুক লোড হচ্ছে…
2

Read Griswold

"The more work put into the steel at the working point the better will be its grade."
3

Forge the blanks

Forge carbon tool steel at no more than a bright red into the shapes of his fig. 2: a 3/8 in. chamfered head, a 2 1/2 in. body and a 1 1/2 in. taper. Heavy centre punch at least 5/8 in. across with a conical point about 3/8 in. at the base; lighter centre punches 3/8 and 1/4 in.; pin punches 1/2, 3/8 (square end), 5/16 and 1/4 in., plus parallel-ended, offset and round-ended ones.

এই ধাপের উপকরণ:

যন্ত্র-ইস্পাতের দণ্ডযন্ত্র-ইস্পাতের দণ্ড1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

কামারের ভাটিকামারের ভাটি
নেহাইনেহাই
হাতুড়িহাতুড়ি
কামারের সাঁড়াশিকামারের সাঁড়াশি
4

Finish before hardening

Do all work except grinding the point now: file each punch to shape and finish it with emery cloth. Keep the striking head slightly rounded so it does not broom.

এই ধাপের উপকরণ:

কোরান্ডাম কাপড়কোরান্ডাম কাপড়1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

রেতি (হাতের রেতি)রেতি (হাতের রেতি)
5

Harden the point

Heat the point to a dull red and plunge only the point, about 1/2 in. (13 mm), into a brine bath.

এই ধাপের উপকরণ:

সম্পৃক্ত লবণজলসম্পৃক্ত লবণজল1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

কামারের ভাটিকামারের ভাটি
কামারের সাঁড়াশিকামারের সাঁড়াশি
বালতিবালতি
6

Run the temper

When the point is black, rub a bright spot with emery cloth on a flat stick and watch the heat from the stock colour it. At straw yellow (460 F) plunge the whole punch in water and keep it moving. If the stock has too little heat, lay it over the furnace to draw the colour.

এই ধাপের উপকরণ:

জলজল1 টুকরা
কোরান্ডাম কাপড়কোরান্ডাম কাপড়1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

বালতিবালতি
কামারের ভাটিকামারের ভাটি
7

Grind the points

Grind the points to shape after hardening without letting the edge turn blue; if it blues, grind back to hard metal.

প্রয়োজনীয় সরঞ্জাম:

টেবিল ঘষাই যন্ত্রটেবিল ঘষাই যন্ত্র
8

Troubleshooting

Punch troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" I, **Amateur Work** (Boston), vol. III (1903-04), pp. 273-275 and fig. 2 (checked on the archive.org scan amateurwork03bostrich). Metric figures and tools are ours.

উপকরণ

4

প্রয়োজনীয় সরঞ্জাম

7

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...