সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Swinging-Tub Partition Churn: Rods to the Still Frame Flap the Dashers as the Hung Tub Swings
Woody

তৈরি করেছেন

Woody

9. নভেম্বর 2026NO
১০
০
০
০
০

Swinging-Tub Partition Churn: Rods to the Still Frame Flap the Dashers as the Hung Tub Swings

William Kelly of Hastings, Michigan, received US 24,127, dated 24 May 1859, for a vibrating churn. The tub hangs by straps from studs on a frame and is swung by its handles. A slide partition divides it in two; a dasher is hinged to each side of the partition, and a rod from each dasher's middle hooks onto the still frame. As the tub swings, the rods make the dashers flap, driving the cream against the partition and through openings at its foot from one side to the other. Holes in the dashers, and channels down through the partition, let air into the cream. This rung builds it with a 20-litre bucket hung on its side in a timber frame.
মধ্যবর্তী
About 1 day, plus printing

নির্দেশাবলি

1

How the dashers flap

Jupyter নোটবুক লোড হচ্ছে…
2

Swinging to work two dashers, before it

Merrill swung a pendulum beside the churn. Kelly swings the tub itself, and the still frame works the dashers.
3

Read US 24,127

"... as the dasher draws near the partition, the space is vacated by the cream passing out through the openings h h h in the partition D alternately from one apartment to the other."
4

Print the guide

A groove for the partition's edge. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
নকশা ফাইলSTLCC0 - Free
5

Print the box f

A journal box for a dasher. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
নকশা ফাইলSTLCC0 - Free
6

Frame

From 40 x 40 mm timber cut two rails A 640 mm long, four legs splayed from 150 mm either side of a rail's middle to 360 mm out at the floor, and two stretchers 440 mm long. Screw the legs to the rails' ends so the rails stand 580-620 mm up, 480 mm apart, and screw the stretchers between the leg pairs 130 mm up. Screw two cross pieces B 520 x 40 x 30 mm across the rails' tops 220 mm apart, and an eye bolt (staple g) under each at its middle. Put an M12 bolt through each rail's middle, pointing in, as the studs c.

এই ধাপের উপকরণ:

নরম কাঠ ৭০x৭০ মিমিনরম কাঠ ৭০x৭০ মিমি4 টুকরা
কাঠের স্ক্রু #10 x 3"কাঠের স্ক্রু #10 x 3"24 টুকরা
চোখওয়ালা বোল্টচোখওয়ালা বোল্ট2 টুকরা
ষড়ভুজ বোল্টের সংগ্রহষড়ভুজ বোল্টের সংগ্রহ2 টুকরা
সমতল ওয়াশারসমতল ওয়াশার4 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
চাঁদাচাঁদা
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
সমন্বয়যোগ্য রেঞ্চসমন্বয়যোগ্য রেঞ্চ
ফিতা-মাপফিতা-মাপ
7

Tub C and cover I

Lay a food-grade 20-litre bucket on its side, its lid snapped on. Cut away its wall above a level 100 mm over its axis to open the top, and file the edge smooth. Screw a flat-bar strap 30 x 6 mm to the middle of the bottom and of the lid, rising to 180 mm above the axis, each drilled 13 mm at the top to hook on a stud. Glue a guide upright in the middle of the bottom and of the lid, inside. Screw a hardwood foot G under the bucket and a hardwood handle H on each side at axis height. Cut a plywood cover I 340 x 250 mm with a slot 78 x 24 mm each side of the middle.

এই ধাপের উপকরণ:

২০ লিটারের বালতি২০ লিটারের বালতি1 টুকরা
নরম ইস্পাতের চ্যাপ্টা পাটানরম ইস্পাতের চ্যাপ্টা পাটা1 টুকরা
যন্ত্র-স্ক্রুযন্ত্র-স্ক্রু8 টুকরা
নাইলন-ভরা লক নাটনাইলন-ভরা লক নাট8 টুকরা
PETG ফিলামেন্টPETG ফিলামেন্ট1 টুকরা
শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু6 টুকরা
প্লাইউডের পাতপ্লাইউডের পাত1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ফিলামেন্টের 3D প্রিন্টার (FDM)ফিলামেন্টের 3D প্রিন্টার (FDM)
জিগস করাতজিগস করাত
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
হ্যাকসহ্যাকস
বেঞ্চ ভাইসবেঞ্চ ভাইস
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
8

Partition D and dashers E

Glue up a hardwood partition D 356 x 231 x 20 mm. Cut three half-round openings h 36 mm across in its foot, 100 mm apart, and drill an 8 mm channel j down from the top edge into each. Screw two journal boxes f on each face 113 mm above the foot, 160 mm apart. Cut two dashers E 100 x 220 mm from 10 mm plywood, drill each with four 24 mm holes i, glue an 8 mm dowel 200 mm long along one long edge as the journal, and glue a small block on top 50 mm from that edge for the rod's hook. Snap the journals into the boxes and slide the partition into its guides.

এই ধাপের উপকরণ:

শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা
প্লাইউডের পাতপ্লাইউডের পাত1 টুকরা
শক্ত কাঠের গোঁজশক্ত কাঠের গোঁজ1 টুকরা
যন্ত্র-স্ক্রুযন্ত্র-স্ক্রু8 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
জিগস করাতজিগস করাত
কোদাল-বিট সেটকোদাল-বিট সেট
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
শিরিষ কাগজশিরিষ কাগজ
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
9

Hang it and fit the rods

Hook the straps over the studs so the tub hangs between the rails. Bend two 6 mm stainless rods with a hook at each end, 224 mm between hooks; put the cover on, pass a rod down each slot and hook it through the dasher's block below and the eye bolt above.

এই ধাপের উপকরণ:

স্টেনলেস স্টিলের দণ্ডস্টেনলেস স্টিলের দণ্ড1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

বেঞ্চ ভাইসবেঞ্চ ভাইস
হ্যাকসহ্যাকস
রেতি (হাতের রেতি)রেতি (হাতের রেতি)
10

The build in 3D

FreeCAD model of this build, the front half cut away: the frame with its studs, cross pieces and eye bolts, the bucket hung on its straps, the cover, the partition in its guides with its foot openings, the two hinged dashers and their rods. It was checked at five swing angles from -15 to +15 degrees.
নকশা ফাইলBLENDCC0 - Free
11

Churn

Lift the cover, pour about 8 litres of heavy cream at about 15 °C into the two halves, checked with the thermometer, and put the cover back over the rods. Take a handle and swing the tub steadily about 15 degrees each way; time it. When the butter comes, unhook the rods, lift out the partition and dashers, unhook the tub, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

এই ধাপের উপকরণ:

ঘন ক্রিমঘন ক্রিম8 l
মোটা সমুদ্র লবণমোটা সমুদ্র লবণ1 টুকরা
জলজল1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ভিতরে রেখে দেওয়া প্রোব থার্মোমিটারভিতরে রেখে দেওয়া প্রোব থার্মোমিটার
স্টপওয়াচস্টপওয়াচ
ডিজিটাল রান্নাঘরের দাঁড়িপাল্লাডিজিটাল রান্নাঘরের দাঁড়িপাল্লা
স্টেনলেস স্টিলের বড় মেশানোর বাটিস্টেনলেস স্টিলের বড় মেশানোর বাটি
12

Troubleshooting

Swinging-tub churn troubleshooting.

Flow

Loading...
13

History and honest limits

**William Kelly** of Hastings, Barry County, Michigan, US 24,127, 24 May 1859. He did not claim working dashers by the churn's swinging as such, only the dashers with the slide partition and rods so joined to the frame. His tub was made cylindrical below the centre and flat on two sides; ours is a bucket on its side. He gave no sizes: every size and material and the 15 degree swing are ours.

উপকরণ

19

প্রয়োজনীয় সরঞ্জাম

18

ডিজাইন ফাইল

3

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...