কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)
Ed

তৈরি করেছেন

Ed

28. অক্টোবর 2026FI
১
০
০
০
০

Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)

A panel push button that closes a circuit only while you press it. A spring holds the button out, and a metal rim on the end of its rod sits clear of two contacts. Press it and the rim bridges both contacts. A second spring inside the button lets the rod give, so the contacts never take more than that spring's force. Source: Frank C. De Reamer, US 2,166,803 (General Electric, 1939), Fig. 5. Unknown: the insulating material, the metals and every size. De Reamer gives none of them, so they are linked to unknown heads. The tools are ours. Picture: the patent's Fig. 5.
উন্নত
2 days

নির্দেশাবলি

1

Mould the housing

Mould a cup-shaped housing of insulating material, with a boss on each of two opposite sides, a recess in the top of each boss, a groove inside below each boss, and a bead round the top. Unknown: the material, the sizes and the moulding.

এই ধাপের উপকরণ:

অজানা অন্তরক উপাদানঅজানা অন্তরক উপাদান1 as required

প্রয়োজনীয় সরঞ্জাম:

কম্প্রেশন ছাঁচকম্প্রেশন ছাঁচ
অজানা মাপঅজানা মাপ
2

Make the terminals and contacts

Bend two angled metal strips. The upper end of each sits in a boss recess, and the lower end is a solder lug. Fix each upper end to a contact that fits the groove inside the housing, stepped at its bottom end. Unknown: the metal.

এই ধাপের উপকরণ:

অজানা ধাতুঅজানা ধাতু1 as required

প্রয়োজনীয় সরঞ্জাম:

পাত কাটার কাঁচিপাত কাটার কাঁচি
চ্যাপ্টা মুখের সাঁড়াশিচ্যাপ্টা মুখের সাঁড়াশি
অজানা মাপঅজানা মাপ
3

Make the sleeve, plate and cover

Turn a threaded sleeve and cut its thread. Spin its lower end over onto a metal plate with tangs. Cut a cover of insulating sheet with ears that reach over the bosses and a hole in the middle to guide the rod.

এই ধাপের উপকরণ:

অজানা ধাতুঅজানা ধাতু1 as required
অজানা অন্তরক উপাদানঅজানা অন্তরক উপাদান1 as required

প্রয়োজনীয় সরঞ্জাম:

ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
লেদ সরঞ্জাম সেট (HSS)লেদ সরঞ্জাম সেট (HSS)
ডাই ধরার হাতলডাই ধরার হাতল
পাত কাটার কাঁচিপাত কাটার কাঁচি
ভার্নিয়ার ক্যালিপারভার্নিয়ার ক্যালিপার
অজানা মাপঅজানা মাপ
4

Make the push button

Make a drawn metal tube closed at the top, and a rod with a head. Put a small coil spring in the top of the tube, then the rod's head. Wedge a washer into the tube under the head. Leave clearance so the rod can swivel a little. Turn the rod's lower end down to a smaller diameter. Unknown: the metal.

এই ধাপের উপকরণ:

অজানা ধাতুঅজানা ধাতু1 as required
সংনমন স্প্রিং সেটসংনমন স্প্রিং সেট1 spring

প্রয়োজনীয় সরঞ্জাম:

ধাতুর খরাদ যন্ত্রধাতুর খরাদ যন্ত্র
লেদ সরঞ্জাম সেট (HSS)লেদ সরঞ্জাম সেট (HSS)
ভার্নিয়ার ক্যালিপারভার্নিয়ার ক্যালিপার
অজানা মাপঅজানা মাপ
5

Assemble

Set the terminals in their recesses and the contacts in their grooves. Slide the button into the sleeve, with a coil spring round the rod between the cover and the wedged washer. Pass the rod's end through the cover's hole. Put on it a loose insulating washer with a metal rim round its edge. Hammer the rod's end over into a flange. Lay the cover on the housing, so its ears clamp the terminals, and bend the plate's tangs over the bead.

এই ধাপের উপকরণ:

অজানা অন্তরক উপাদানঅজানা অন্তরক উপাদান1 as required
অজানা ধাতুঅজানা ধাতু1 as required
সংনমন স্প্রিং সেটসংনমন স্প্রিং সেট1 spring

প্রয়োজনীয় সরঞ্জাম:

বেঞ্চ ভাইসবেঞ্চ ভাইস
গোল মাথার হাতুড়িগোল মাথার হাতুড়ি
চ্যাপ্টা মুখের সাঁড়াশিচ্যাপ্টা মুখের সাঁড়াশি
সুরক্ষা চশমাসুরক্ষা চশমা
6

Mount and wire it

Put the sleeve through a hole in the panel and clamp the panel between two nuts on the thread. Solder the bared wire ends to the two lugs.

এই ধাপের উপকরণ:

ষড়ভুজ বাদামষড়ভুজ বাদাম2 pcs
সোল্ডার তারসোল্ডার তার1 as required

প্রয়োজনীয় সরঞ্জাম:

ঝালাইয়ের ছড়ঝালাইয়ের ছড়
চ্যাপ্টা মুখের সাঁড়াশিচ্যাপ্টা মুখের সাঁড়াশি
7

Check it

At rest, the rim sits against the underside of the cover and the circuit is open. Pressed, the rim meets the stepped ends of both contacts and closes it. The checking is ours: the meter reads open, then closed while pressed.

প্রয়োজনীয় সরঞ্জাম:

মাল্টিমিটারমাল্টিমিটার

উপকরণ

5

প্রয়োজনীয় সরঞ্জাম

13

এই ব্লুপ্রিন্ট যা তৈরি করে

সম্পর্কিত ব্লুপ্রিন্ট

এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...