সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য

Butterfly-Wing Churn: Two Dashers Hinged to an Adjustable Bar Flap Together From One Crank
Josiah Stubbs of Dublin, Indiana, received US 24,673, dated 5 July 1859, for a churn with two dashers hinged to a central bar like a butterfly's wings. The bar slides on notched stays inside the shell and is set so the cream barely covers it. One crank on the side works both dashers through two rods, one crossing the churn on a slant. Going down, the cream rushes round the dashers' edges against the shell; going up, flanges on the dashers carry cream up and throw it together.
This rung builds it in a 20-litre bucket.
মধ্যবর্তী
About 6 hours, plus printing
নির্দেশাবলি
1
1
Setting the bar for the cream you have
Setting the bar for the cream you have
Jupyter নোটবুক লোড হচ্ছে…
2
2
Hinged, flapping dashers, before it
Hinged, flapping dashers, before it
Kelly flapped hinged dashers by swinging the tub. Stubbs keeps the shell still and flaps them from a crank.
3
3
Read US 24,673
Read US 24,673
"As the dashers are drawn upwardly, a portion of the fluid will be retained upon them, by means of the flanges (e) and thrown violently together as the dashers reach their upper extremity of motion".
4
4
Print the flange
Print the flange
A quarter of a dasher's flange e. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
5
5
Stays and bar b
Stays and bar b
Screw two hardwood stays a 24 x 15 mm, 337 mm long, upright inside the bucket on opposite sides, and saw notches a' 6 mm wide and 4 mm deep in their inner faces every 20 mm from 60 to 220 mm up. Cut a hardwood bar b 272 x 20 x 16 mm with a slotted block 44 mm wide at each end to slide on the stays, and fit an M5 set screw c with a wing nut through one block to hold it in a notch.
এই ধাপের উপকরণ:
২০ লিটারের বালতি1 টুকরা
শক্ত কাঠের তক্তা1 টুকরা
কাঠের স্ক্রু6 টুকরা
কাঠের আঠা1 টুকরা
যন্ত্র-স্ক্রু1 টুকরা
প্রজাপতি নাট1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
হাত-করাত
বাটালি
তারবিহীন তুরপুন
ড্রিল-বিট সেট
স্ক্রুড্রাইভার সেট
ফিতা-মাপ6
6
Dashers d d
Dashers d d
Cut two half-discs 244 mm across from 12 mm plywood and trim each to 220 mm along its straight edge. Glue the printed flanges e round their curved edges, standing 15 mm up. Hinge each dasher's straight edge to one side of the bar with two stainless butt hinges, 4 mm clear of the bar. Screw a small hardwood eye block on each dasher 100 mm out from the bar's middle, the right one 30 mm toward the front, the left one 40 mm toward the back.
এই ধাপের উপকরণ:
প্লাইউডের পাত1 টুকরা
PETG ফিলামেন্ট1 টুকরা
কাঠের আঠা1 টুকরা
দরজার কবজা4 টুকরা
কাঠের স্ক্রু16 টুকরা
শক্ত কাঠের তক্তা1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
ফিলামেন্টের 3D প্রিন্টার (FDM)
জিগস করাত
তারবিহীন তুরপুন
ড্রিল-বিট সেট
শিরিষ কাগজ
স্ক্রুড্রাইভার সেট7
7
Crank h k and rods g g'
Crank h k and rods g g'
Drill the bucket's wall 13 mm 315 mm up, 30 mm toward the front, and fit a 12 mm stainless shaft through a hardwood bearing block outside, sealed. Fix a hardwood crank arm h 35 mm between centres on the inner end with a 8 mm pin pointing inward, and a crank handle k outside. Bend two 6 mm stainless rods with an eye at each end: g 185 mm between eyes from the pin to the right dasher, g' 262 mm from the pin across the churn on a slant to the left dasher.
এই ধাপের উপকরণ:
স্টেনলেস স্টিলের দণ্ড1 টুকরা
শক্ত কাঠের তক্তা1 টুকরা
শক্ত কাঠের গোঁজ1 টুকরা
যন্ত্র-স্ক্রু2 টুকরা
নাইলন-ভরা লক নাট2 টুকরাপ্রয়োজনীয় সরঞ্জাম:
তারবিহীন তুরপুন
ড্রিল-বিট সেট
বেঞ্চ ভাইস
হ্যাকস
রেতি (হাতের রেতি)
স্ক্রুড্রাইভার সেট8
8
The build in 3D
The build in 3D
FreeCAD model of this build, the near side of the bucket cut away: the notched stays, bar b, the two hinged dashers with their flanges, the crank inside the wall and the two rods, one crossing on a slant. It was checked at eight crank angles.
9
9
Churn
Churn
Pour in about 8 litres of heavy cream at about 15 °C, checked with the thermometer, and set the bar in the notch the notebook gives so the cream barely covers it. Put the lid on and turn the crank steadily; time it. When the butter comes, lift the bar and dashers out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
এই ধাপের উপকরণ:
ঘন ক্রিম8 l
মোটা সমুদ্র লবণ1 টুকরা
জল1 টুকরাপ্রয়োজনীয় সরঞ্জাম:
ভিতরে রেখে দেওয়া প্রোব থার্মোমিটার
স্টপওয়াচ
ডিজিটাল রান্নাঘরের দাঁড়িপাল্লা
স্টেনলেস স্টিলের বড় মেশানোর বাটি10
10
Troubleshooting
Troubleshooting
Butterfly-wing churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Josiah Stubbs** of Dublin, Wayne County, Indiana, US 24,673, 5 July 1859, "Churn". He claimed working the butterfly wings with a single crank on one side, the rod g' crossing the cylinder on a slant. He gave no sizes or materials: every size, the notches' spacing and the crank's throw are ours.
উপকরণ
16- 1 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 22 টুকরাপ্লেসহোল্ডার
- 2 টুকরাপ্লেসহোল্ডার
- 3 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 2 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 4 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 2 টুকরাপ্লেসহোল্ডার
- 8 lপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
- 1 টুকরাপ্লেসহোল্ডার
প্রয়োজনীয় সরঞ্জাম
16- প্লেসহোল্ডার
- প্লেসহোল্ডার
- 1 vendor sell this, none ship to you yetপ্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- 1 vendor sell this, none ship to you yetপ্লেসহোল্ডার
- প্লেসহোল্ডার
- 1 vendor sell this, none ship to you yetপ্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
- প্লেসহোল্ডার
ডিজাইন ফাইল
2এই ব্লুপ্রিন্ট যা তৈরি করে
সম্পর্কিত ব্লুপ্রিন্ট
এই ব্লুপ্রিন্টগুলি জ্ঞান ভাগ করে — কৌশল, উপকরণ বা নীতি
CC0 পাবলিক ডোমেন
এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।
মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।



