সহযোগিতা
কলা
সৌন্দর্য এবং সুস্থতা
ক্রাফট
সংস্কৃতি ও ইতিহাস
বিনোদন
পরিবেশ
খাদ্য ও পানীয়
রিভার্স ইঞ্জিনিয়ারিং
বিজ্ঞান
খেলাধুলা
টেকনোলজি
পরিধানযোগ্য
Rubber-Pipe Pump Churn: A Pulley Rolls Milk Through a Tube in a Ring and Jets It Through Gauze
Buttercup

তৈরি করেছেন

Buttercup

9. নভেম্বর 2026IE
১০
০
০
০
০

Rubber-Pipe Pump Churn: A Pulley Rolls Milk Through a Tube in a Ring and Jets It Through Gauze

Loren J. Wicks of Racine, Wisconsin, received US 24,686, dated 5 July 1859, for a churn that is a rolling-tube pump. An india-rubber pipe runs from the bottom of the milk box once round the groove inside a ring and up into a smaller box on top. A pulley on a fast crank rolls round the ring on the pipe and drives the milk up in a stream against two gauze partitions hung under the top box's cap. The broken milk runs back through a screen of fine wooden strips into the box below, the butter staying behind; the stream keeps going until all the butter is out. This rung builds it with silicone tubing, a printed ring and pulley, and pine boxes.
মধ্যবর্তী
About 1 day, plus printing

নির্দেশাবলি

1

A rolling pulley as a pump

Jupyter নোটবুক লোড হচ্ছে…
2

A churn that pumps the cream round, before it

McClintock pumped with a vane and valves. Wicks squeezes a rubber pipe and needs no valve at all.
3

Read US 24,686

"Thus it will plainly be seen that in the manner which pipe (B) passes round circular frame (F) the pulley when rolling on it will force the milk up into box (C)."
4

Print the frame F

The ring with the tube's groove round its inside and the hole in its foot. PETG, 0.2 mm layers, 50 % infill, 5 walls; wash before first use.
নকশা ফাইলSTLCC0 - Free
5

Print the rotor

The hub with the two projections that carry the pulley. PETG, 0.2 mm layers, 50 % infill, 5 walls; wash before first use.
নকশা ফাইলSTLCC0 - Free
6

Print the pulley H

The pulley that rolls on the tube. PETG, 0.2 mm layers, 50 % infill, 5 walls; wash before first use.
নকশা ফাইলSTLCC0 - Free
7

Stand and boxes

From pine make box A 360 x 240 mm inside and 230 mm deep, and stand it on four 44 mm legs 400 mm tall. Drill a 13 mm hole near the front of its floor. Make box C 360 x 122 mm inside and 180 mm deep, with a floor, and stand it on two cleats across A's back, leaving A open for 100 mm in front of it. Cut C's front out between 18 and 122 mm up and glue hardwood strips 6 mm wide upright in the opening, 4 mm apart, as screen D. Drill C's front 13 mm above the screen for a 8 mm stainless spout.

এই ধাপের উপকরণ:

পাইন কাঠের তক্তাপাইন কাঠের তক্তা3 টুকরা
নরম কাঠ ৭০x৭০ মিমিনরম কাঠ ৭০x৭০ মিমি2 টুকরা
কাঠের আঠাকাঠের আঠা1 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু40 টুকরা
শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
স্টেনলেস স্টিলের নলস্টেনলেস স্টিলের নল1 টুকরা
সিলিকন সিল্যান্টসিলিকন সিল্যান্ট1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

হাত-করাতহাত-করাত
জিগস করাতজিগস করাত
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
ক্ল্যাম্পক্ল্যাম্প
শিরিষ কাগজশিরিষ কাগজ
ফিতা-মাপফিতা-মাপ
8

Cap I and partitions E

Cut a plywood cap 340 x 100 mm to slide on C's top. Make two frames 240 x 138 mm from 3 mm plywood with a window in each, staple stainless mesh over the windows (for his tin and gauze), and screw them upright under the cap 40 mm apart, across the jet's path.

এই ধাপের উপকরণ:

প্লাইউডের পাতপ্লাইউডের পাত1 টুকরা
তারের জালতারের জাল1 টুকরা
কাঠের স্ক্রুকাঠের স্ক্রু8 টুকরা

প্রয়োজনীয় সরঞ্জাম:

জিগস করাতজিগস করাত
পাত কাটার কাঁচিপাত কাটার কাঁচি
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
9

Frame F, pulley and pipe B

Screw a pine board across the front legs below box A and screw the printed frame F on its front, 220 mm up. Bore the board for a 12 mm stainless shaft G with a hardwood support K behind it, fit the rotor and pulley H on its pin inside the frame and a hardwood crank P outside. Push 12 x 8 mm silicone tubing into A's floor hole, sealed, down through a hole in the board and the hole in F's foot, once round the groove, out through the same hole, round the outside of F and up to C's spout.

এই ধাপের উপকরণ:

পাইন কাঠের তক্তাপাইন কাঠের তক্তা1 টুকরা
PETG ফিলামেন্টPETG ফিলামেন্ট1 টুকরা
স্টেনলেস স্টিলের দণ্ডস্টেনলেস স্টিলের দণ্ড2 টুকরা
শক্ত কাঠের তক্তাশক্ত কাঠের তক্তা1 টুকরা
শক্ত কাঠের গোঁজশক্ত কাঠের গোঁজ1 টুকরা
যন্ত্র-স্ক্রুযন্ত্র-স্ক্রু3 টুকরা
নাইলন-ভরা লক নাটনাইলন-ভরা লক নাট3 টুকরা
সিলিকন নলসিলিকন নল1 টুকরা
সিলিকন সিল্যান্টসিলিকন সিল্যান্ট1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ফিলামেন্টের 3D প্রিন্টার (FDM)ফিলামেন্টের 3D প্রিন্টার (FDM)
তারবিহীন তুরপুনতারবিহীন তুরপুন
ড্রিল-বিট সেটড্রিল-বিট সেট
হ্যাকসহ্যাকস
কাজের ছুরিকাজের ছুরি
স্ক্রুড্রাইভার সেটস্ক্রুড্রাইভার সেট
10

The build in 3D

FreeCAD model of this build, half the boxes cut away: box A on its stand, box C with screen D, the cap and the two mesh partitions, the board with frame F, the rotor and pulley on the shaft, the crank, and the tube's run from A's floor round the ring and up to C. The rotor was checked at six angles.
নকশা ফাইলBLENDCC0 - Free
11

Churn

Pour about 10 litres of cream at about 15 °C into box A, checked with the thermometer. Turn the crank fast and time it: a stream jets into C against the mesh and runs back through the screen. Slide the cap back and forth now and then. When the butter is held in C, stop, lift C off, take the butter out, pour the buttermilk from A, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

এই ধাপের উপকরণ:

ঘন ক্রিমঘন ক্রিম10 l
মোটা সমুদ্র লবণমোটা সমুদ্র লবণ1 টুকরা
জলজল1 টুকরা

প্রয়োজনীয় সরঞ্জাম:

ভিতরে রেখে দেওয়া প্রোব থার্মোমিটারভিতরে রেখে দেওয়া প্রোব থার্মোমিটার
স্টপওয়াচস্টপওয়াচ
ডিজিটাল রান্নাঘরের দাঁড়িপাল্লাডিজিটাল রান্নাঘরের দাঁড়িপাল্লা
স্টেনলেস স্টিলের বড় মেশানোর বাটিস্টেনলেস স্টিলের বড় মেশানোর বাটি
12

Troubleshooting

Rubber-pipe pump troubleshooting.

Flow

Loading...
13

History and honest limits

**Loren J. Wicks** of Racine, Wisconsin, US 24,686, 5 July 1859, "Churn". He did not claim forcing milk in a stream against a substance as such, only boxes A and C with pipe B, and box C with screen D and the hanging partitions E. His pipe was india rubber and his partitions tin and gauze; our silicone tubing, mesh frames, printed ring and pulley and every size are ours.

উপকরণ

18

প্রয়োজনীয় সরঞ্জাম

16

ডিজাইন ফাইল

4

CC0 পাবলিক ডোমেন

এই ব্লুপ্রিন্ট CC0-এর অধীনে প্রকাশিত। আপনি অনুমতি ছাড়াই যেকোনো উদ্দেশ্যে এটি অনুলিপি, পরিবর্তন, বিতরণ ও ব্যবহার করতে পারেন।

মেকারের ব্লুপ্রিন্টের মাধ্যমে পণ্য কিনে তাঁকে সমর্থন করুন, যেখানে তিনি আয় করেন মেকার কমিশন বিক্রেতাদের নির্ধারিত, অথবা এই ব্লুপ্রিন্টের একটি নতুন সংস্করণ তৈরি করে নিজের ব্লুপ্রিন্টে সংযোগ হিসেবে যুক্ত করে আয় ভাগ করুন।

আলোচনা

(0)

লগ ইন করুন আলোচনায় যোগ দিতে

মন্তব্য লোড হচ্ছে...