Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Angle Grinder: Reversible, with a Hollow Arbour and a Top Arbour Lock (Turley, US 5,718,621)
Forge

Criado por

Forge

9. novembro 2026NO
7
0
0
0
0

Angle Grinder: Reversible, with a Hollow Arbour and a Top Arbour Lock (Turley, US 5,718,621)

An angle grinder spins a disc at right angles to its motor: a bevel gear on the motor shaft turns a bevel gear on an upright arbour. E. M. Turley (US 5,718,621, 1998) makes the arbour hollow. A bolt runs down through it into a hexagonal coupling piece that drives the disc and clamps it against the arbour's flange, so the motor can run either way without loosening the disc. To change the disc, a sliding lock piece on top locks the arbour, opens a hole over the bolt head and switches the motor off in one move. Source: E. M. Turley, "Reversible Angle Grinder with Top Arbour Lock", US Patent 5,718,621 (filed 1996, granted 1998). Picture: its Fig. 1.
Avançado
Unknown

Instruções

1

Read Turley

"The angle grinder according to the preferred embodiment of the invention includes a reversible motor driving a hollow arbour via a right angle bevel gear arrangement. The arbour has a right angle flange at its bottom. The flange abuts against one side of the disk tool."
2

Turn the hollow arbour

Turn an arbour hollow all through, with three outside shoulders (lower, middle and upper) for the two bearings and the bevel gear, and grooves above each for a snap ring. At the bottom, enlarge the bore into a hexagonal recess ending in a right-angle flange. At the top, enlarge the bore so the bolt head sits below the rim, and cut four equally spaced square notches (crenellations) in the rim. Sizes and metal are not given.

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 arbour

Ferramentas necessárias:

Torno mecânicoTorno mecânico
FresadoraFresadora
Limas (lima de mão)Limas (lima de mão)
Dimensões desconhecidasDimensões desconhecidas
3

Make the coupling piece and bolt

Make a coupling piece: a hexagonal upper part that fits the arbour's recess, a round pilot that fits the standard centre hole of commercial grinding discs, and a right-angle flange at its base. Bore and tap it from the top, closed at the bottom. Make a retaining bolt long enough to run from the arbour's top down into the coupling piece, threaded at its lower end (Fig. 1 draws a socket in its head).

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 coupling piece
Metal desconhecidoMetal desconhecido1 retaining bolt

Ferramentas necessárias:

Torno mecânicoTorno mecânico
FresadoraFresadora
Jogo de machos e cossinetesJogo de machos e cossinetes
Dimensões desconhecidasDimensões desconhecidas
4

Cut the bevel gears

Cut two bevel gears with teeth at forty-five degrees (equal gears for a right-angle drive): one fixed on the arbour against its middle shoulder, one on the front end of the motor shaft. Tooth count and metal are not given.

Materiais para este passo:

Metal desconhecidoMetal desconhecido2 bevel gears

Ferramentas necessárias:

FresadoraFresadora
Fresa para engrenagens cónicasFresa para engrenagens cónicas
Dimensões desconhecidasDimensões desconhecidas
5

Assemble the drive

Mount a reversible electric motor in the housing, its shaft running back in a rear bearing and forward in a front bearing, the bevel gear on its front end. Set the arbour upright in two bearings at its lower and upper shoulders, the bevel gears meshing, with snap rings above the bearings and the gear. Drop the bolt down the arbour on a lock washer, fit the coupling piece from below and screw it on. Motor rating, housing material and how the bearings are held are not given.

Materiais para este passo:

Motor elétricoMotor elétrico1 reversible
Rolamento de esferasRolamento de esferas4 peças
Material desconhecidoMaterial desconhecido1 housing

Ferramentas necessárias:

Jogo de chaves AllenJogo de chaves Allen
Método de conformação desconhecidoMétodo de conformação desconhecido
Dimensões desconhecidasDimensões desconhecidas
6

Fit the arbour lock

Make a rectangular lock piece that slides in the housing top across the arbour head, with a lever up through a slot in the housing, a tool hole, and a square tang underneath that drops into a rim notch. A spring on its front face holds it back in the running position. Fix a two-contact power switch to its rear so the motor circuit is broken when the piece is slid into the locking position. Cut a hole in the housing top over the bolt head and a slot for the lever.

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 lock piece
MolaMola1 peça
Interruptor de ligar/desligarInterruptor de ligar/desligar1 peça

Ferramentas necessárias:

FresadoraFresadora
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Limas (lima de mão)Limas (lima de mão)
7

Change a disc

Push the lever forward: the tang locks the arbour, the switch cuts the motor and the tool hole sits over the bolt head. Unscrew the bolt from above with the key and pull the coupling piece; put the new disc on its pilot and screw it back up tight, so the disc is clamped between the arbour flange and the coupling flange. Let the lever spring back to run. Turley: a loose bolt cannot drop the disc, which rattles to warn you to tighten it.

Ferramentas necessárias:

Jogo de chaves AllenJogo de chaves Allen

Materiais

6

Ferramentas necessárias

10

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...