Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Arc Welder: AC Transformer with a Sliding Shunt Core (Fanger, US 2,248,070)
Forge

Criado por

Forge

9. novembro 2026NO
4
0
0
0
0

Arc Welder: AC Transformer with a Sliding Shunt Core (Fanger, US 2,248,070)

An AC arc welder is a step-down transformer whose current can be turned up and down. H. J. Fanger (US 2,248,070, 1941) cuts a gap through one leg of a laminated ring core and slides a laminated iron shunt bar through it: pushed in, it carries flux past the secondary and lowers the welding current; pulled out, the current rises. For arc welding he gives about 60 to 68 volts open circuit, 15 to 200 amps, dropping to 38 or 40 volts at the working arc, with a small coil on the shunt bar in series with the secondary. Source: H. J. Fanger, "Welding Transformer", US Patent 2,248,070 (filed 1938, granted 1941). Picture: its Figs. 1-5.
Avançado
Unknown

Instruções

1

Read Fanger

"With arc welding, infinite control of the volume of the secondary current, between maximum and minimum is obtained by adjustment of the slidable shunt core without altering the welding characteristics of the current, also better ignition of the arc is had at a given voltage, and greater stability of the arc".
2

Stack the core

Build a single rectangular ring core of insulated iron laminations, held together with brass (or insulated) bolts or rivets in insulating tubes (Fig. 4). Cut a gap straight through one leg, accurately machined and finished, and make a circular joint through the opposite leg with the segments staggered to overlap in successive laminations. Core size, lamination iron and thickness are not given (ours: the tools).

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 iron laminations
Sortido de parafusos sextavadosSortido de parafusos sextavados1 brass bolts
Material isolante desconhecidoMaterial isolante desconhecido1 insulating tubes

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Limas (lima de mão)Limas (lima de mão)
Dimensões desconhecidasDimensões desconhecidas
3

Make the shunt bar

Make the sliding shunt section of the same laminated iron, a snug fit in the gap with its laminations edge-to-edge with the core's, and long enough to fill the gap at every position. Sheath both sides with a slightly wider plate of Bakelite that overlaps the edges of the gap to guide it. Fit a threaded rod on its outer end, working in a nut fixed to the section (or move it by hand, with calibration marks along one edge).

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 shunt laminations
BaqueliteBaquelite2 side plates
Sortido de parafusos sextavadosSortido de parafusos sextavados1 brass bolts
Varão roscadoVarão roscado1 peça
Porca sextavadaPorca sextavada1 peça

Ferramentas necessárias:

Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Limas (lima de mão)Limas (lima de mão)
4

Wind the coils

Wind the primary and secondary windings on both legs of the core (Fig. 2), in series or in parallel to suit the line voltage and the current wanted. Wind a small auxiliary coil round the shunt bar's path, fixed so the bar slides through it, and connect it in series with the secondary through a reversing switch (some jobs weld better with the current through it one way). Turns and wire sizes are not given.

Materiais para este passo:

Fio de cobreFio de cobre1 insulation and size not given

Ferramentas necessárias:

Dimensões desconhecidasDimensões desconhecidas
5

Spring the joints

On both sides of the gap and of the circular joint fit pairs of confronting angle plates, held by brass bolts in insulating sleeves and drawn together by spring bolts whose heads rest on slightly arched spring plates, so the joints close snugly on the sliding bar. A small lever on the gap-joint nut gives a half turn to release the bar for moving. The angle-plate material is not given.

Materiais para este passo:

Material desconhecidoMaterial desconhecido4 angle plates
Sortido de parafusos sextavadosSortido de parafusos sextavados1 brass and spring bolts
Material isolante desconhecidoMaterial isolante desconhecido1 sleeves
Fita de aço-molaFita de aço-mola1 arched spring plates
Porca sextavadaPorca sextavada4 peças

Ferramentas necessárias:

Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Chave inglesaChave inglesa
6

Connect and set

Connect the primary to the line through a line switch, and the secondary leads to the electrode holder and the work. Pull the shunt bar out for more current, push it in for less: Fanger gives about 60-68 volts open circuit and 15-200 amps, dropping to 38-40 volts at the arc.

Materiais para este passo:

Interruptor de ligar/desligarInterruptor de ligar/desligar1 line switch

Ferramentas necessárias:

Chave inglesaChave inglesa

Materiais

10

Ferramentas necessárias

6

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...