ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Articulated Hand Model
Emma

Criado por

Emma

28. julho 2026SE
1
0
0
0
0

Articulated Hand Model

Open and close your hand and watch the back of your forearm. Something moves there, well above the wrist. That is the surprise this model is built to make obvious: there are no muscles inside your fingers at all.

Fingers are bones, joints, ligaments and tendons. The engines sit in the forearm and pull on long cables that run through the wrist and out to the fingertips. It is remote actuation, and it is the same solution a cable-driven robot arm uses for exactly the same reason — you cannot afford the mass at the far end.

Cut card fingers, thread cord through straw segments for tendon sheaths, and pull. The hand closes. Release, and elastic on the back opens it again — because a cable can only pull, never push.

Iniciante
2 hours

Instruções

1

Trace your own hand flat on card

Spread your fingers and draw around them. Life size is the right size — you can check every proportion against the original.

Materiais para este passo:

Cardstock Assorted Pack (50 Sheets)Cardstock Assorted Pack (50 Sheets)2 folhas
2

Feel for your own knuckles and mark them

Bend each finger and mark where it actually creases. Three joints per finger, two for the thumb — and the first knuckle is much further back in the palm than most people draw it.

Ferramentas necessárias:

Measuring RulerMeasuring Ruler
3

Cut out the hand outline

Cut cleanly around the traced shape, keeping the palm intact as one piece.

Ferramentas necessárias:

Craft KnifeCraft Knife
4

Score across each joint line, do not cut through

Press a blunt point along each mark to make a hinge. Score on the back of the hand so the finger folds toward the palm and not away from it.

5

Cut straw into short segments

Cut 10-15 mm lengths of drinking straw. These are your tendon sheaths — the tunnels that keep the cord running close to the bone.

Materiais para este passo:

Paper Drinking StrawsPaper Drinking Straws6 peças
6

Glue segments along the palm side of each finger

Stick one segment to each bone section, leaving each joint clear. A straw glued across a joint locks it — the gaps are what allow bending.

Materiais para este passo:

PVA Wood GluePVA Wood Glue10 ml
7

Add a run of segments across the palm to the wrist

Continue the tunnel from each finger down the palm. All five cords should emerge together at the wrist, exactly as the real flexor tendons do through the carpal tunnel.

8

Thread cord from fingertip to wrist

Run a length of cotton cord through each finger's straws. Tie a knot at the fingertip large enough not to pull back through.

Materiais para este passo:

Kitchen Twine (Cotton)Kitchen Twine (Cotton)3 metros
9

Pull one cord and watch the finger curl

Draw the cord at the wrist. The whole finger rolls up joint by joint — you have not moved anything inside the finger, only pulled at the far end.

10

Notice the finger will not straighten by itself

Release the cord and nothing happens. A cable can only pull. A one-cable finger is a one-way finger, and this is the moment the design problem becomes obvious.

11

Fit elastic along the back of each finger

Glue a light elastic strip from fingertip to knuckle on the back. This is the extensor side, and now releasing the cord springs the finger open.

Materiais para este passo:

Elastic CordElastic Cord1 metro
12

Attach a forearm board and pin the cords to it

Fasten the palm to a strip of card representing the forearm and bring all five cords to it. The controls now sit where your real muscles sit.

Materiais para este passo:

Brass Paper FastenersBrass Paper Fasteners6 peças
13

Pull all five at once to make a fist

Gather the cords into a ring and pull. The hand closes as a unit — and holding the ring is exactly the grip a cable-driven prosthetic gives its wearer.

14

Test the thumb separately

Try to make the thumb touch each fingertip. It will not, because your model's thumb joint is a hinge and the real one is a saddle. Note what is missing rather than fudging it.

Ferramentas necessárias:

Notebook and PencilNotebook and Pencil
15

Compendium — the engines are in the forearm

Twenty-seven bones and no finger muscles. Each hand has 27 bones: 8 carpals in the wrist, 5 metacarpals in the palm, and 14 phalanges — three in each finger, two in the thumb. The muscles that curl and straighten the fingers are the extrinsic muscles, and their bellies lie in the forearm; only their tendons continue into the hand. There are intrinsic muscles inside the palm — the lumbricals, interossei and thenar group — which handle spreading, fine positioning and the thumb, but the powerful flexion of a grip comes from the forearm. This is why a clenched fist makes the forearm bulge and the fingers do not.

Why evolution put them there. Mass at the end of a limb is expensive: it must be accelerated and decelerated with every movement, and it raises the moment of inertia about the wrist. Moving the actuators back toward the body and transmitting force through tendons keeps the fingers slim and quick. Robotics arrived at the same answer independently — most dexterous robot hands are cable-driven or tendon-driven for exactly this reason, and the ones that put a motor in each finger joint end up bulky and slow.

Antagonistic pairs are not optional. A tendon can pull and cannot push, so every joint needs at least two opposing actuators. In the hand the flexor digitorum profundus and superficialis curl the finger and the extensor digitorum straightens it. Your elastic strip plays the extensor's part. The same constraint governs every muscle in the body — biceps against triceps, and so on — and it is a genuine engineering limitation, not a quirk of anatomy.

What the model cannot show. The carpometacarpal joint of the thumb is a saddle joint, allowing opposition — the ability to bring the thumb pad against each fingertip, which underpins precision grip. A card hinge cannot reproduce it. The real tendons also run in synovial sheaths lubricated well enough that friction is nearly negligible, whereas cotton cord in a paper straw binds noticeably. Both gaps are worth naming: a model that hides its own limits teaches the wrong lesson.

Materiais

6

Ferramentas necessárias

3

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...