Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)
Woody

Criado por

Woody

4. novembro 2026NO
11
0
0
0
0

Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)

A shop belt sander for dressing wood surfaces: a 6 in garnet-paper belt running over four crowned wooden pulleys, one driven by the lathe, pressed down onto the work with a hand float. Best belt speed about 2,500 ft per minute; leave about 1 in between work and belt. Source: Popular Mechanics Shop Notes for 1919, p. 3235. Picture: the article's drawing.
Intermediário
Unknown

Instruções

1

Turn the pulleys

Build up four solid wood pulleys 10 in across with 8 in faces and turn them in the lathe with a very slight crown; too much crown harms the belt.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei4 built-up pulleys

Ferramentas necessárias:

Torno de madeiraTorno de madeira
2

Mount the pulleys

Mount one pulley on a firmly held arbor in the lathe and the other three on iron-pipe shafts on a frame (drawing). Turn and file a true journal on each pipe, pour babbitt bushings in the pulleys, and cut oil grooves in the pipe or babbitt. Supporting the shafts on one side lets the belt slip off; supporting both sides is stronger.

Materiais para este passo:

Tubo de aço (de parede grossa, com roscas)Tubo de aço (de parede grossa, com roscas)3 shafts
Metal desconhecidoMetal desconhecido1 babbitt bushings
Madeira de pinhoMadeira de pinho1 frame

Ferramentas necessárias:

Lima para metalLima para metal
Escumadeira perfuradaEscumadeira perfurada
SerroteSerrote
MarteloMartelo
3

Make the belt

Cut 6 in garnet paper (No. 1 1/2 for general work) so the ends just meet over the pulleys. Glue the smooth side at the joint, splice it with a strip of cloth about 1 in wide and then one about 3 in wide, cover each side with paper, and clamp between two small boards.

Materiais para este passo:

LixaLixa1 6 in garnet paper
Pano de algodãoPano de algodão1 peça
Cola animalCola animal1 peça

Ferramentas necessárias:

Grampo em CGrampo em C
4

Set up and run

Run the belt at about 2,500 ft per minute using the lathe's cone pulley. Set the work about 1 in below the belt on a table or a low sliding platform (two sets of tongue-and-groove joints at right angles), start the machine and press the belt down with a float like a blackboard eraser, or a roller.

Materiais para este passo:

Madeira de pinhoMadeira de pinho1 platform, float

Ferramentas necessárias:

Torno de madeiraTorno de madeira

Materiais

7

Ferramentas necessárias

6

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...