Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Bench Glassblowing Torch: Brass Gas Blowpipe with a Glass Air Jet (Shenstone, 1916)
A glassblower's gas blowpipe you can make yourself: a brass tube with a side tube for gas, and a glass air jet down its middle fed from a foot-blower. A fine jet gives the small pointed flame for joints, and a wider jet the big brush flame for heating large tubes. It is pegged into a wooden block on a sheet-iron-covered bench, with taps for gas and air at the bench edge.
Result: a bench blowpipe for working glass tube. Make two: one about 11 mm bore for small work, one 15 to 17 mm for large.
Source: W. A. Shenstone, The Methods of Glass-Blowing (1916), pp. 3-9. Unknown: the brazing metal and the tap type. Picture: Fig. 1 of the book.
Intermediário
Unknown
Instruções
1
1
Braze the gas inlet
Braze the gas inlet
Take a brass tube for the body: about 11 mm bore for the small blowpipe, 15 to 17 mm for the large one. Braze a side tube for the gas onto it 10 to 12 cm from the back end, according to the tube's size. Fix a spike to it for mounting. Ours: borax as the flux. Not given: the brazing metal.
Materiais para este passo:
Tubo de latão1 body and side tube
Metal desconhecido1 brazing metal and spike
Bórax em pó1 brazing fluxFerramentas necessárias:
Serra de arco para metais
Forja2
2
Fit the glass air jet
Fit the glass air jet
Fit a glass tube down the middle of the brass tube, held by a cork at the back end, its tip near the mouth. For the small pointed flame, draw the tip down to the size of a large knitting needle. For a large flame rich in air, the tip may be nearly half the bore of the brass tube. Make several air tubes of different sizes for each blowpipe.
Materiais para este passo:
Tubo de vidro3 air jets of several sizes
Rolhas1 jet corkFerramentas necessárias:
Bico de Bunsen3
3
Set up the bench
Set up the bench
Cover the bench round the blowpipe with sheet iron. Drill several holes in a block of wood so the spike can be set at different positions. Fix two taps near the bench edge, one for gas and one for air. Connect them by flexible tubes to the supplies on one side and to the blowpipe's gas inlet and air jet on the other. Ours: mild steel sheet, rubber tubing. Not given: the tap type.
Materiais para este passo:
Chapa de aço macio1 bench cover
Bloco de madeira dura1 mounting block
Válvula desconhecida2 gas and air taps
Tubo de borracha1 flexible tubesFerramentas necessárias:
Engenho de furar4
4
Light it and blow
Light it and blow
Light the gas at the mouth and work a foot-blower to drive air through the glass jet into the burning gas. Little air and a small jet give the pointed flame; plenty of gas and a strong blast give the large, non-luminous brush flame.
Ferramentas necessárias:
FoleMateriais
9- 1 body and side tubeReferência
- 1 brazing metal and spikeReferência
- 1 brazing fluxReferência
- 3 air jets of several sizesReferência
- 1 jet corkReferência
- 1 bench coverReferência
- 1 mounting blockReferência
- 2 gas and air tapsReferência
- 1 flexible tubesReferência
Ferramentas necessárias
5- Referência
- Referência
- Referência
- Referência
- Referência
Materiais de Blueprints conectados

10% de atribuição
Venetian Borax: Refining Tincal with Lime
por Charlie
Inorgânico
22
0
0
0
1
0

10% de atribuição
Natural Rubber Tubing, Bands and Sheet: Sulfur-Cured with Heat
por Mary
Química
16
0
0
0
2
0

10% de atribuição
Oak Boards and Blocks, Milled and Air-Dried
por Woody
Marcenaria
45
0
0
0
3
0

10% de atribuição
Building a Box Bellows — The Breath That Makes Metal Obey Fire
por Emma
Marcenaria
108
0
0
0
8
0
Este projeto faz
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.
