Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Closet Shoe Rack: Wedge-Shaped Pockets on the Wall With a Slatted Bottom for Dirt to Fall Through (Boy Mechanic, 1913)
Woody

Criado por

Woody

13. novembro 2026NO
5
0
0
0
0

Closet Shoe Rack: Wedge-Shaped Pockets on the Wall With a Slatted Bottom for Dirt to Fall Through (Boy Mechanic, 1913)

A shoe rack "that can be placed on the wall in the clothes closet", from The Boy Mechanic (1913): two boards 9 in wide and about 3 ft long, held apart by six wedge-shaped partitions so the pockets open wider at the top, and a slatted bottom that lets the dirt fall through. Sizes are the book's. Contributed to Popular Mechanics by Guy H. Harvey of Mill Valley, California.
Iniciante
About 2 hours

Instruções

1

The partitions

A carregar o notebook Jupyter…
2

Read The Boy Mechanic

"Two boards, 9 in. wide and about 3 ft. long, with six partitions between, as shown, will make pockets about 6 in. long. The width of the pockets at the bottom is 2 in. and at the top 5 in."
3

Cut the boards and partitions

Cut two pine boards 9 in wide and about 3 ft long, the back and the front. Cut six partitions as wedges from the notebook, 9 in tall, 2 in deep at the bottom and 5 in at the top.

Materiais para este passo:

Tábua de pinhoTábua de pinho1 peça

Ferramentas necessárias:

Fita métricaFita métrica
LápisLápis
Esquadro fixoEsquadro fixo
SerroteSerrote
4

Assemble the pockets

Nail the partitions to the back board, square to it, one at each end and the rest spaced about 6 in apart. Nail the front board to their sloping edges, so it leans out and the pockets open wider at the top.

Materiais para este passo:

PregosPregos1 peça

Ferramentas necessárias:

Martelo de unhaMartelo de unha
5

Fit the slatted bottom

Nail strips across the bottom of the pockets with gaps between them, as his Fig. 1, so the dirt from the shoes falls through.

Materiais para este passo:

Ripa de madeira duraRipa de madeira dura1 peça
PregosPregos1 peça

Ferramentas necessárias:

SerroteSerrote
Martelo de unhaMartelo de unha
6

Hang it

Screw the back board to the wall of the clothes closet (ours), and put a pair of shoes toe-down in each pocket.

Materiais para este passo:

Parafusos para madeiraParafusos para madeira1 peça

Ferramentas necessárias:

Berbequim de mãoBerbequim de mão
Conjunto de chaves de fendasConjunto de chaves de fendas
7

Troubleshooting

Shoe rack troubleshooting.

Flow

Loading...
8

History and honest limits

From **The Boy Mechanic, Volume 1**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1913 (Project Gutenberg #12655), "Homemade Shoe Rack", contributed by Guy H. Harvey of Mill Valley, California. The board sizes, pocket sizes and six partitions are the book's; the wood, nails, slat sizes and hanging screws are ours.

Materiais

4

Ferramentas necessárias

7

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...