Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)
Woody

Criado por

Woody

13. novembro 2026NO
6
0
0
0
0

Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)

E. E. Hulgan's lathe from The Boy Mechanic, Book 2 (1915), "in which wood and light metal articles may be turned": a 5 ft bed of two 2 by 4 in hardwood rails, a headstock clamped by bolts with a 3/4 in steel spindle in brass bearings and a three-step pulley, a bolted hardwood tailstock with a screw-fed dead centre, a sliding tool rest, and a screw-on chuck. Driven from a countershaft or by foot.
Avançado
About 1-2 weeks

Instruções

1

His sizes, and the pulley speeds

A carregar o notebook Jupyter…
2

Read The Boy Mechanic, Book 2

"A strong, substantial lathe in which wood and light metal articles may be turned can be made by carefully following the description below and the detailed drawings of the parts."
3

Make the bed

Cut two pieces of straight-grained, smooth 2 by 4 in hardwood, 5 ft long, and hold them apart at each end with blocks of wood 2 in wide (Fig. 9 shows 2 in rails with a 2 in gap). The bed can be longer or shorter.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Parafusos para madeiraParafusos para madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Plaina manualPlaina manual
Berbequim de mãoBerbequim de mão
Fita métricaFita métrica
4

Build the headstock frame

Make the two hardwood end pieces to the shape of Figs. 1 and 2 (2 in thick, 2 in apart on an 8 in base, 7-1/2 in high, 6 in wide at the bottom) and screw them to the base. Nail a slider 1 in thick and 10 in long, just wide enough to slide between the bed rails, under the base, 2 in from its rear end. Bore two 1/2 in holes through base and slider and put two 1/2 in bolts through them and through another slide and board under the bed, so tightening the nuts clamps the headstock. Screw a half-round wedge-shaped brace inside the frame against the front end.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Parafuso de carroçariaParafuso de carroçaria2 peças
Porca sextavadaPorca sextavada2 peças
Parafusos para madeiraParafusos para madeira1 peça
PregosPregos1 peça

Ferramentas necessárias:

SerroteSerrote
FormõesFormões
Arco de pua e brocaArco de pua e broca
Berbequim de mãoBerbequim de mão
5

Make the spindle and bearings

Make the spindle of tool steel or steel tubing, 3/4 in in diameter and 14 in long, and cut a thread on one end. Rivet on a hardened steel collar, 1/4 by 1-1/2 in, to turn against another collar of the same size on the headstock; screw a third collar to the rear end piece and fix a collar with a removable pin on the spindle, fitted to turn easily with no end play. Drill brass tubing for the spindle as bearings and wedge them into the headstock 6 in above the bed, in line; drill small oil holes from the top.

Materiais para este passo:

Barra de aço-ferramentaBarra de aço-ferramenta1 peça
Tubo de açoTubo de aço1 peça
Shaft CollarShaft Collar4 peças
Rebites de açoRebites de aço1 peça
Tubo de latãoTubo de latão1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de machos e cossinetesJogo de machos e cossinetes
Berbequim de mãoBerbequim de mão
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
MarteloMartelo
6

Fit the stepped pulley

Make the pulleys 2 in wide, with the diameters on the drawing: 6, 4-1/2 and 3 in. Fasten them to the spindle with a removable pin. (Turned hardwood is our choice of material; he does not say.)

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça

Ferramentas necessárias:

SerroteSerrote
Arco de pua e brocaArco de pua e broca
Berbequim de mãoBerbequim de mão
7

Make the chuck and centres

For the chuck (Fig. 3), take shafting 1-1/2 in in diameter and 2-1/2 in long, drill a 1/2 in hole through its centre, ream and thread one end to fit the spindle, and fit a setscrew over the 1/2 in hole. Make a wood-turning centre, and other centres and drills, from 1/2 in tool steel.

Materiais para este passo:

Barra redonda de aço macioBarra redonda de aço macio1 peça
Barra de aço-ferramentaBarra de aço-ferramenta1 peça
Parafuso sem cabeça de ponta côncavaParafuso sem cabeça de ponta côncava1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Berbequim de mãoBerbequim de mão
AlargadorAlargador
Jogo de machos e cossinetesJogo de machos e cossinetes
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
8

Build the tailstock

Build the tailstock (Figs. 4-6) of three pieces of hardwood 2 in thick and one 1 in thick, shaped as drawn, held together with four bolts 7-1/2 in long. Give it sliders and clamp it to the bed like the headstock, but with one bolt, and weld a handle to its nut for easy clamping. Drill a piece of tubing 2 in long for a 1/2 in dead centre and set it 1-1/2 in into the joint between the two upper pieces. Bore for a 1/2 in bolt to slide in the tube; chisel a recess behind the tube for a 1/2 in nut; turn a bolt 7 in long, threaded for 2 in, into nut and tube, and rivet a handle or wheel on its end. Make the centre of 1/2 in tool steel with a tapered point.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Parafuso de carroçariaParafuso de carroçaria5 peças
Porca sextavadaPorca sextavada2 peças
Tubo de açoTubo de aço1 peça
Barra de aço-ferramentaBarra de aço-ferramenta1 peça
Rebites de açoRebites de aço1 peça

Ferramentas necessárias:

SerroteSerrote
FormõesFormões
Arco de pua e brocaArco de pua e broca
Berbequim de mãoBerbequim de mão
Forja a carvãoForja a carvão
BigornaBigorna
Martelo de ferreiroMartelo de ferreiro
Limas (lima de mão)Limas (lima de mão)
9

Make the tool rest

The tool rest (Figs. 7-9) has a slide 3/4 by 3 by 13 in with a slot 1/2 by 6 in. Bolt the rest base on the slide so it can be adjusted, and screw the rest to the base. Raise or lower it with wedges between slide and base, and clamp it to the bed like the tailstock.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Parafuso de carroçariaParafuso de carroçaria1 peça
Porca sextavadaPorca sextavada1 peça
Parafusos para madeiraParafusos para madeira1 peça

Ferramentas necessárias:

SerroteSerrote
FormõesFormões
Arco de pua e brocaArco de pua e broca
10

Troubleshooting

Wood lathe troubleshooting.

Flow

Loading...
11

History and honest limits

From "How to Make a Wood Lathe" by E. E. Hulgan, Marion, Ind., in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 434-436). Part shapes come from his Figs. 1-9; he gives no pulley material and no countershaft or foot-drive details. The pulley material, tools and metric figures are ours.

Materiais

12

Ferramentas necessárias

15

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...