Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)
Woody

Criado por

Woody

13. novembro 2026NO
7
0
0
0
0

Jointed Fishing Rods: Two- and Three-Piece Casting, Trout and Bass Fly, Salt-Water and Tarpon Rods (Boy Mechanic, 1915)

Part II of Stillman Taylor's rod-making series (The Boy Mechanic, Book 2, 1915): once the one-piece casting rod is mastered, the same planing, grasp and finishing methods make jointed rods. He gives full caliper tables and fitting lists for six rods; choose one in the notebook. Sections join with welted, shouldered ferrules, and every rod gets two tips "in view of a possible breakage".
Avançado
About 2-3 weeks (glue and varnish drying)

Instruções

1

His caliper tables

A carregar o notebook Jupyter…
2

Read The Boy Mechanic, Book 2

"While the action of the one-piece rod is undeniably better than when the rod is made in two or three pieces, it is less compact to carry." He warns that "the more joints incorporated in a rod, the less satisfactory it will be from an angling standpoint", since ferrules cannot follow the rod's curve.
3

Choose the rod and get the stock

Pick a rod from the notebook. Stock (dagame or greenheart): two-piece casting -- butt 5/8 in x 3 ft, two tips 3/8 in x 3 ft; three-piece casting -- all 2 ft, butt 5/8 in, joint and tips 3/8 in; trout or bass fly -- butt 5/8 in x 4 ft, joint and tips 3/8 in x 4 ft; salt-water -- both 4 ft, butt 3/4 in, tip 1/2 in; tarpon -- one piece 1 in x 6-1/2 ft.

Materiais para este passo:

Madeira de dagameMadeira de dagame4 peças

Ferramentas necessárias:

SerroteSerrote
Fita métricaFita métrica
4

Plane each section to its table

Plane, round and scrape each section exactly as for the one-piece rod, calipering at every station in the table. Two-piece casting rod: he first suggests a butt of about 23 in and a 32-1/2 in tip to fit a 35 in rod case, then specifies a 6-1/2 oz rod with a 32-1/2 in butt (15/32 in at the grasp to 19/64 in at the ferrule) and a 33 in tip (17/64 in to 7/64 in), equal when ferrule and top are on. Make two tips for each rod.

Materiais para este passo:

LixaLixa1 peça

Ferramentas necessárias:

Plaina manualPlaina manual
Plaina de blocoPlaina de bloco
Raspador de açoRaspador de aço
Limas (lima de mão)Limas (lima de mão)
PaquímetroPaquímetro
5

Fit the ferrules

Fit a welted, shouldered ferrule at each joint, sized from his list: 17/64 in for the two-piece casting rod; 21/64 in and 15/64 in for the three-piece; 9/32 in and 11/64 in for the fly rods; 7/16 in for the salt-water rod; a 3/4 in male ferrule on the tarpon butt. The tip ferrule comes with two closed-end centres, one for each tip. Cement them on with ferrule cement; serrated (toothed) ferrule ends are wound with silk for strength.

Materiais para este passo:

Virola de encaixe da canaVirola de encaixe da cana2 peças
Cola para virolasCola para virolas1 peça
Seda para atar canasSeda para atar canas1 peça

Ferramentas necessárias:

Limas (lima de mão)Limas (lima de mão)
Maçarico a propanoMaçarico a propano
PaquímetroPaquímetro
6

Build the grasp and reel seat

Build the cork grasp and reel seat as for the one-piece rod: 3/4 in reel seat with straight hood for the casting rods (fly-rod type with butt cap on the fly rods, 9 in or 9-1/2 in of cork above it), 7/8 in on the salt-water rod with an 18 in double grasp, 1 in on the tarpon rod. Use a 1 in butt cap (1-1/8 in on the tarpon rod) and a taper (winding check) of the small-end size in his list. For an independent butt, fit the ferrule straight on a rounded dagame core so the seated ferrule does not touch the wood, cement and rivet it, fit a soft-pine sleeve over core and ferrule, glue it on, cement and rivet the reel seat, then glue on the corks and cut the core flush.

Materiais para este passo:

Anéis de cortiçaAnéis de cortiça24 peças
Cola animalCola animal1 peça
Tábua de pinhoTábua de pinho1 peça
Porta-carretoPorta-carreto1 peça
Tampa do punho da canaTampa do punho da cana1 peça
Anel de remate da pegaAnel de remate da pega1 peça
Cola para virolasCola para virolas1 peça
Rebites de cobreRebites de cobre1 peça

Ferramentas necessárias:

X-ato (faca de precisão)X-ato (faca de precisão)
Berbequim de mãoBerbequim de mão
Plaina de blocoPlaina de bloco
Maçarico a propanoMaçarico a propano
MarteloMartelo
7

Mount the guides and tops

Casting rods: two 1/2 in narrow agate guides, two No. 1 one-ring casting guides and two 3/32 in offset agate tops. Fly rods: two No. 4 snake guides on the butt joint, three No. 3 on the middle joint, three No. 2 on each tip, and two No. 7 agate angle fly tops of the wind-on kind. Salt-water rod: a 10/32 in stirrup-tube agate top and two No. 3 bell guides. Tarpon rod: two No. 11 wide raised agate guides, two No. 1 trumpet guides and a 3/8 in agate stirrup top; whip its guides on double, the first set 10 in from the top, the second 26 in from the reel. Whip with 00 silk (00 or 0 on the three-piece rod, size A on the salt-water and tarpon rods), using the invisible knot.

Materiais para este passo:

Passador de canaPassador de cana8 peças
Passador de ponteiraPassador de ponteira2 peças
Seda para atar canasSeda para atar canas1 peça
Cera de abelhaCera de abelha1 peça

Ferramentas necessárias:

Limas (lima de mão)Limas (lima de mão)
X-ato (faca de precisão)X-ato (faca de precisão)
8

Shellac and varnish

Shellac the windings and varnish the rod with coach varnish as for the one-piece rod: thin coats, warm, three days between coats.

Materiais para este passo:

Verniz de goma-lacaVerniz de goma-laca1 peça
Verniz de carruagemVerniz de carruagem3 peças

Ferramentas necessárias:

Trincha largaTrincha larga
9

Troubleshooting

Jointed rod troubleshooting.

Flow

Loading...
10

History and honest limits

From "Fishing-Rod Making and Angling, Part II" by Stillman Taylor, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 69-72). Two points are given as he wrote them: the two-piece casting rod's butt is about 23 in in one sentence and 32-1/2 in in the next; the three-piece rod's stock is "2 ft. long" while its finished sections are 21-1/2, 21-3/4 and 21 in. Guide counts in the list are for the fly rods, the largest set. The tools and metric figures are ours.

Materiais

17

Ferramentas necessárias

12

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...