Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)
George J. Egelberg's ski sled from The Boy Mechanic, Book 3 (1919): "built low and wide so that it will not tip easily", on two 10 ft by 6 in ash runners boiled and bent like skis, set on knee blocks with a slight rocker, and topped with three 6 in boards.
Intermediário
About 2 days
Instruções
1
1
His sizes, and the rocker
His sizes, and the rocker
A carregar o notebook Jupyter…
2
2
Read The Boy Mechanic, Book 3
Read The Boy Mechanic, Book 3
"The skis, or runners, are cut 10 ft. long and 6 in. wide, from 1-in. ash boards that are straight-grained."
3
3
Thin the bend
Thin the bend
Cut two runners 10 ft long and 6 in wide from straight-grained 1 in ash. Where the curve will be, plane about 1/4 in off the upper side, but not at the very tip, so the skis bend more easily.
Materiais para este passo:
Tábua de madeira de lei2 peçasFerramentas necessárias:
Serrote
Plaina manual
Fita métrica
Lápis4
4
Boil and bend
Boil and bend
If steaming is not handy, boil the skis with at least 1-1/2 ft of the points under water and the vessel covered so little steam escapes, for at least one hour. Take them out, put them side by side in the bending blocks at once and bend with slow, even pressure; weight the long ends and leave them 8 or 10 hours to dry. Sharpen the points after bending.
Materiais para este passo:
Tábua de pinho1 peçaFerramentas necessárias:
Panela grande
Sargento de barra
Plaina manual5
5
Set the blocks and top
Set the blocks and top
For a slight rocker, make the centre knee block 6 in high and the two end blocks 5-1/2 in. Run a 1/4 in flat-head bolt through the ski, the block and the cross strip, countersinking the heads in the running surface. Make the top of three 6 in boards fastened to the crosspieces, and brace the ski tips with a 2 in strip.
Materiais para este passo:
Tábua de madeira de lei1 peça
Tábua de pinho3 peças
Parafuso de carroçaria6 peças
Anilha plana6 peças
Parafusos para madeira1 peçaFerramentas necessárias:
Serrote
Berbequim de mão
Conjunto de brocas de escarear
Martelo6
6
Troubleshooting
Troubleshooting
Ski sled troubleshooting.
Flow
Loading...
7
7
History and honest limits
History and honest limits
From "A Ski Sled" by George J. Egelberg, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, p. 41). The bending-block shape and knee pieces come from his drawing. The tools and metric figures are ours.
Materiais
5- 2 peçasReferência
- 3 peçasReferência
- 6 peçasReferência
- 6 peçasReferência
- 1 peçaReferência
Ferramentas necessárias
9- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
Este projeto faz
Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.


