Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Clamp-On Countersink: Two Blocks Screwed Round Any Drill, Twin Cutters Countersink the Hole as It Is Bored (Brackin, 1903)
George W. Brackin of Philadelphia received US 727,580, dated 12 May 1903, for a countersink that clamps onto a drill or auger bit. Two blocks are screwed together across the bit at any point along it. A twin cutter is screwed into an inclined seat in each block, its point reaching into the bit's flutes. As the bit bores, the cutters arrive and cut the cone for the screw head without taking the bit out. A slotted stop sets how deep it goes, so it gauges the hole too.
We make three for 4, 5 and 6 mm drills. The patent gives no sizes; every size here is ours.
Intermediário
About 1 day
Instruções
1
1
Setting it on the bit
Setting it on the bit
A carregar o notebook Jupyter…
2
2
Read US 727,580
Read US 727,580
"From Figs. 2 and 3 it will be observed that the lower ends of the inclined cutters project slightly into the twists or helical channels of the drill, and this fact permits the cutters to enter the hole bored and then commence cutting away the edge of the hole as the tool is rotated."
3
3
Clamping blocks 2 and 3
Clamping blocks 2 and 3
For each attachment cut two blocks 40 x 12 x 10 mm from square bar. In each, 6 mm from one end drill a 4.5 mm plain hole and 6 mm from the other end drill 3.3 mm and tap M4, through the 12 mm face, so the two blocks screw together with the plain hole of one over the tapped hole of the other. Across the middle of each block's outer face file a seat 6 mm wide, sloping down and in at 45 degrees, and drill and tap M4 in it for the cutter's screw.
Materiais para este passo:
Barra quadrada de aço macio1 peçaFerramentas necessárias:
Serra de arco para metais
Torno de bancada
Ponta de traçar
Punção de centro
Engenho de furar
Jogo de brocas
Jogo de machos e cossinetes
Desandador de machos
Jogo de limas
Transferidor
Paquímetro digital de 6 polegadas4
4
Twin cutters 8 and 9
Twin cutters 8 and 9
Cut four cutters 22 mm long from 3 x 6 mm carbon steel strip. Drill each 4.5 mm for its screw at the top, and grind the lower end to a point with a straight cutting edge 13 on its leading side and a rounded back 15, as his Fig. 4. Harden: heat to a cherry red, until a magnet no longer sticks, quench in water, rub bright, and draw to a light straw colour.
Materiais para este passo:
Fita de aço-carbono1 peçaFerramentas necessárias:
Serra de arco para metais
Engenho de furar
Jogo de brocas
Esmeriladora de bancada
Forja
Tenaz de forja
Íman pequeno
Balde de têmpera
Água
Pedra de amolar
Luvas de soldador
Óculos de segurança5
5
Stop 17 and assembly
Stop 17 and assembly
Bend a strip of 3 mm flat bar into an L, its upright 30 mm long with a 4.5 mm slot 18 15 mm long, its foot 20 mm. Screw a cutter into each block's seat. Put the blocks either side of the drill, the stop's slot under one clamping screw, and screw them together until they grip the drill, the cutters' points just in the flutes and their edges leading as the drill turns.
Materiais para este passo:
Barra chata de aço macio1 peça
Parafusos de máquina4 peçasFerramentas necessárias:
Serra de arco para metais
Torno de bancada
Engenho de furar
Jogo de brocas
Jogo de limas
Conjunto de chaves de fendas6
6
Bore and countersink
Bore and countersink
Set the drill's point the hole's depth below the stop's foot and the cutters for the screw head's size (the notebook gives both). Drill into hardwood until the stop touches: the hole is at depth and its mouth countersunk. Check a screw sits flush.
Ferramentas necessárias:
Berbequim sem fios
Jogo de brocas
Tábua de madeira de lei
Paquímetro digital de 6 polegadas
Óculos de segurança7
7
Troubleshooting
Troubleshooting
Clamp-on countersink troubleshooting.
Flow
Loading...
8
8
History and honest limits
History and honest limits
**George W. Brackin** of Philadelphia, US 727,580, dated 12 May 1903, filed 18 June 1902. He claimed "the rectangular clamping-blocks arranged parallel to each other, clamping-screws passing through the said blocks near their ends", each block "provided exteriorly at its middle point with a cutter-seat inclined downwardly and inwardly", and "duplicate and interchangeable cutters" screwed into them. His was for wood, with the note that the cutters could be hardened for metal; ours are hardened. He gives no sizes or angle; every size here is ours.
Materiais
4- Referência
- 1 peçaReferência
- 1 peçaReferência
- 4 peçasReferência
Ferramentas necessárias
23- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
Este projeto faz
Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

