ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways
Martin

Criado por

Martin

6. outubro 2026NO
2
0
0
0
0

Counter-Rotating Egg Beater: One Wheel, Two Beaters Turning Opposite Ways

A single whisk carries the egg round with it rather than cutting through it. James F. Monroe of Fitchburg, Massachusetts, and E. P. Monroe of New York received US 23,694, dated 19 April 1859, for an egg beater: a frame clamped to a table carries a bevel wheel turned by a handle, gearing into two pinions on opposite sides of it; one turns an inner beater of bent wires, the other an outer beater round it, "in opposite directions." This rung works out the beater speeds, then prints the crown wheel and pinions, bends the beaters, and times a beating.
Intermediário
About 5 hours, plus printing

Instruções

1

Beater speeds

A carregar o notebook Jupyter…
2

The gear train it uses

The embedded blueprint works gear ratios and direction. Monroe takes two pinions off opposite sides of one wheel so they turn opposite ways.
3

Read US 23,694

"This invention consists in arranging in an adjustable frame two beaters, one inside the other, which receive motion in opposite directions by means of two pinions which gear into a large bevel wheel and on opposite sides of the same, so that by rotating the bevel wheel by means of a handle the beaters receive the required motion."
4

Print the gears

Print the 48-tooth crown wheel (/uploads/blueprints/counter-rotating-egg-beater-crown-wheel.stl) and two 12-tooth pinions (/uploads/blueprints/counter-rotating-egg-beater-pinion.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.

Materiais para este passo:

Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
5

Build the frame

Cut a plywood upright and two arms. Bolt the crown wheel to the upright on an M5 screw with washers so it turns freely, and fix a handle screw near its rim. Drill the arms 5 mm on the line through both pinions' centres.

Materiais para este passo:

Placa de contraplacadoPlaca de contraplacado1 peça
Parafusos de máquinaParafusos de máquina1 peça
Anilha planaAnilha plana1 peça
Porca sextavadaPorca sextavada1 peça
Parafuso para madeira n.º 8 x 1"Parafuso para madeira n.º 8 x 1"1 peça

Ferramentas necessárias:

Serra de recortesSerra de recortes
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Chave inglesa ajustávelChave inglesa ajustável
Conjunto de chaves de fendasConjunto de chaves de fendas
6

Arbor and inner beater

Cut 200 mm of 5 mm rod. Epoxy one pinion on it to mesh at the wheel's top, and bend two wire loops 28 mm across at its lower end.

Materiais para este passo:

Varão de aço macioVarão de aço macio1 peça
Arame de aço inoxidávelArame de aço inoxidável1 peça
Epóxi de dois componentesEpóxi de dois componentes1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Alicate de bicos redondosAlicate de bicos redondos
Alicate de bico chatoAlicate de bico chato
7

Sleeve and outer beater

Glue the second pinion to a length of silicone tube sleeved loosely over the rod, meshing at the wheel's bottom. Bend two wire loops 48 mm across and fix them to the sleeve's lower end, round the inner beater.

Materiais para este passo:

Tubo de siliconeTubo de silicone1 peça
Arame de aço inoxidávelArame de aço inoxidável1 peça
Epóxi de dois componentesEpóxi de dois componentes1 peça

Ferramentas necessárias:

Alicate de bicos redondosAlicate de bicos redondos
Alicate de bico chatoAlicate de bico chato
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
8

The patent drawing

US 23,694 drawing sheet, public domain (expired patent).
Passo 8 - Image 1
9

Beat egg whites

Clamp the frame to the table over the bowl with two egg whites. Turn the handle about once a second and time how long until they hold stiff peaks.
Passo 9 - Image 1

Materiais para este passo:

OvoOvo2 peças

Ferramentas necessárias:

Taça grande de aço inoxidávelTaça grande de aço inoxidável
CronómetroCronómetro
10

Beaters that turn together, jam or clash

Counter-rotating egg beater troubleshooting.

Flow

Loading...
11

History and honest limits

**James F. Monroe** of Fitchburg, Massachusetts, and **E. P. Monroe** of New York, assignors to E. P. Monroe, received US 23,694, dated 19 April 1859, reissued 16 October 1860 (No. 1,062). The frame's fork clamps to a table with a set screw and washer. The second pinion lies loose on the arbor, driving the outer beater whose lower collar turns loosely round the arbor's end. They noted it also mixes paint. **Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A crown wheel and spur pinions stand in for his bevel gears, and a silicone sleeve for his loose pinion. Your times are the result.

Materiais

11

Ferramentas necessárias

12

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...