Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Diagonal-Blade Shouldered-Breaker Churn: Pitched Blades on Uneven Arms Turn Under the Shoulders of Two Breakers
Buttercup

Criado por

Buttercup

11. novembro 2026IE
4
0
0
0
0

Diagonal-Blade Shouldered-Breaker Churn: Pitched Blades on Uneven Arms Turn Under the Shoulders of Two Breakers

Lester Day of Buffalo, New York, received US 26,970, dated 31 January 1860, for a churn. An upright shaft carries short upper arms and long lower arms, each with a rectangular blade set diagonally and adjustable along it, the two of a pair at different distances so neither follows the other's track. Two breakers, joined at the top and lifting out together, stand opposite each other with stepped shoulders under which the blades turn, and holes the cream is thrown through. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days, plus printing

Instruções

1

Blades that never follow each other's track

A carregar o notebook Jupyter…
2

Short blades within, a long one under, two months before

Jebb's thick staves are part of the tub. Day's breakers stand free, step back in two shoulders, and lift out.
3

Read US 26,970

"Motion being given to the dash blades by means of the crank and gearing, in the direction of the arrows, they will by their diagonal position on the arms throw the cream or milk outward against the side of the barrel and against the breakers, part passing through the space between the breakers and the side of the barrel, and part being thrown through the holes (h) in the breakers and part being thrown back by the breakers meeting these currents causing a concussion between them"
4

Print the wheel J

Crown wheel, 36 teeth on its face, module 2, with a hub bored 12.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
5

Print the pinion I

Spur pinion, 12 teeth, module 2, with a 12.4 mm square socket for the shaft's top. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Print the foot step b

A cup 60 mm across and 25 mm tall with a 21 mm socket for the shaft's foot. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
7

Tub A, breakers E and cross piece F

Use a wooden tub 360 mm across inside and 450 mm deep; glue the foot step in the middle of its floor and two hardwood sockets g opposite each other against the wall. Cut two breakers from 15 mm hardwood, 420 mm tall, their outer edges 10 mm off the wall: from the top down to 350 mm up their inner edges reach 40 mm from the middle, then step out at H to 118 mm, and at H' (165 mm up) to 150 mm. Bore two 30 mm holes h through each at 220 and 290 mm up. Screw a cross piece 336 x 40 x 20 mm across their tops, bored 32 mm in the middle, and stand them in the sockets leaning slightly. Fill the tub with water overnight so it swells tight, then empty it.

Materiais para este passo:

Tina de madeiraTina de madeira1 peça
Tábua de madeira de leiTábua de madeira de lei2 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira12 peças
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra tico-ticoSerra tico-tico
Serra de mesaSerra de mesa
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Fita métricaFita métrica
ÁguaÁgua
8

Shaft B, arms C and blades D

Turn a hardwood shaft 30 mm across and 500 mm long, its foot turned to 19 mm and its top 40 mm cut to a 12 mm square. Bore it across for two 16 mm hardwood arms at 300 mm up, 204 mm long, and two at 110 mm up at right angles, 272 mm long. Cut eight blades 90 x 70 x 10 mm, bore each through its middle at 45 degrees to its face for the arm, and slide them on: the upper pair at 50 and 62 mm from the shaft, the lower at 84 and 96 mm, the nearer and farther blade on opposite sides. Pin each where it sits.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura2 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Torno de madeiraTorno de madeira
Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
LixaLixa
Fita métricaFita métrica
9

Cover L, gear frame K and crank M

Cut a cover to sit on the rim, bored 32 mm in its middle, held by two hooks and eyes. Screw two chairs on it in a line from the middle, carrying a 12 mm stainless shaft with the crown wheel and a crank, and drop the pinion over the shaft's square top so they mesh. Lift the cover off to free the shaft; lift the breakers out by the cross piece to clean them.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Colchete (macho e fêmea)Colchete (macho e fêmea)2 peças
Parafusos para madeiraParafusos para madeira8 peças
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
BússolaBússola
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Conjunto de chaves de fendasConjunto de chaves de fendas
10

The build in 3D

FreeCAD model of this build, the tub and cover cut through the middle: the two shouldered breakers with their holes and cross piece, the shaft with its short upper and long lower arms and diagonal blades, the foot step, and the crown wheel, pinion and crank on the cover. The dash was turned through 24 positions.
Arquivo de designBLENDCC0 - Free
11

Churn

Pour about 15 litres of heavy cream at about 15 °C into the tub, checked with the thermometer, put the cover on and hook it. Turn the crank steadily in the blades' direction, timing it. When the butter comes, lift the cover, dash and breakers out, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater15 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
12

Troubleshooting

Shouldered-breaker churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Lester Day** of Buffalo, Erie County, New York, US 26,970, 31 January 1860, "Churn". He claimed the breakers E with shoulders H, H', fixed to the cross piece F and removable with it, and the adjustable diagonal dash blades D working with them. His blades may also be turned on their arms to throw the cream upward, or inward and downward when reversed. His bevel wheel and pinion are here a printed crown wheel and pinion. The patent gives no sizes; every size here is ours.

Materiais

11

Ferramentas necessárias

19

Ficheiros de design

4

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...