Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Distillation Column Assembly: Flask, "Evaporator" Still-Head, Liebig Condenser and Receivers (Young, 1903)
Charlie

Criado por

Charlie

3. novembro 2026DE
10
0
0
0
0

Distillation Column Assembly: Flask, "Evaporator" Still-Head, Liebig Condenser and Receivers (Young, 1903)

A complete fractional distillation set: a globular flask, Young and Thomas's 'evaporator' still-head built of stacked glass sections, a Liebig condenser and a row of receivers. In each section the rising vapour is forced through the liquid running back down, so the mixture separates better at each step. Result: a fractionating apparatus for separating liquids by boiling point, the fractions caught in receivers changed at set temperatures. Source: S. Young, Fractional Distillation (1903), pp. 4-7, 115-116, 166-168. Picture: Figs. 37 and 38 of the book.
Avançado
Unknown

Instruções

1

Choose the still

Use a globular flask, since a flat-bottomed one may crack over a naked flame, no larger than the amount of liquid needs. Fit it with a cork for the still-head. Ours: a round-bottom flask.

Materiais para este passo:

Balão de fundo redondoBalão de fundo redondo1 still
RolhasRolhas1 still cork

Ferramentas necessárias:

Bico de BunsenBico de Bunsen
2

Blow the evaporator still-head

Build the still-head of sections joined end to end. Each outer tube is 22 to 24 mm inside and about 10 to 10.5 cm long, constricted at the bottom. In it stands a thin inner tube, 7.5 to 8 mm inside and 60 mm long, open at both ends, with two large holes near its top. Its lower end widens into a funnel resting on the constriction, with three or four tiny glass beads fused to the rim so it does not fit too tightly. Over it stands an intermediate tube about 14 mm inside and 50 mm long, like a small inverted test tube. A small funnel, slightly wider than the dip in the outer tube above, sits on top of it on three glass legs. Small glass projections centre the tubes. Make the head long enough that the thermometer's bulb and stem both sit in the vapour, with a side delivery tube at the top.

Materiais para este passo:

Tubo de vidroTubo de vidro1 sections, inner and intermediate tubes, delivery tube

Ferramentas necessárias:

Maçarico de vidreiro de bancadaMaçarico de vidreiro de bancada
3

Fit the condenser

Use a Liebig condenser, about 7 or 8 mm inside for the inner tube and 15 mm for the outer, cooled by running water. Pass the delivery tube through a cork into it. Draw out the joint where the wide inlet meets the narrow tube so no pool of liquid lies there. Bend the narrow tube so the condenser can stand upright. Above about 170 °C use a long tube cooled by air instead of water.

Materiais para este passo:

Condensador resfriado a águaCondensador resfriado a água1 condenser
RolhasRolhas1 condenser cork

Ferramentas necessárias:

Maçarico de vidreiro de bancadaMaçarico de vidreiro de bancada
ÁguaÁgua
4

Set the heat and the receivers

Heat with a Bunsen burner, its top about 2 mm below the flask so the small flame touches the glass, shielded from draughts. Add a few pieces of porous porcelain (a broken clay pipe will do) or pumice if the liquid bumps. Set a thermometer in the still-head and a row of small flasks as receivers.

Materiais para este passo:

TermómetroTermómetro1 still-head thermometer
Balão de recolhaBalão de recolha10 receivers

Ferramentas necessárias:

Bico de BunsenBico de Bunsen
Material desconhecidoMaterial desconhecido
5

Distil in fractions

Read the barometer and correct the set temperatures for it. Distil steadily. In each section, condensed liquid seals the narrow passage, so the vapour rises up the inner tube, down between the tubes and up again, while liquid drips from section to section back to the still. Collect the distillate in fractions, changing the receiver each time the temperature reaches one of the values fixed beforehand.

Ferramentas necessárias:

Barómetro de mercúrioBarómetro de mercúrio
Bico de BunsenBico de Bunsen
ÁguaÁgua

Materiais

6

Ferramentas necessárias

5

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...