Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Brick Smith's Hearth: Stone Base, Firebrick Top in an Iron Rim, a Cannon-Shot Tuyere and a Slake Trough (Edwinson, 1886)
Forge

Criado por

Forge

14. novembro 2026NO
6
0
0
0
0

Brick Smith's Hearth: Stone Base, Firebrick Top in an Iron Rim, a Cannon-Shot Tuyere and a Slake Trough (Edwinson, 1886)

The fixed smith's hearth George Edwinson told Amateur Work readers to build (1886): stone below, firebrick in fireclay on top, every course bound with hoop iron, a 4 in. iron rim forming the hearth pan, a fire back and tuyere made from a 1 in. plate and a bored 14-pounder iron shot, a slanting flue, a 10 x 10 x 22 in. slake trough, and a clinker floor.
Intermediário
Two to three days of building

Instruções

1

His sizes

A carregar o notebook Jupyter…
2

Read Edwinson

"The foundation of this structure up to within one foot of the top may be of stone, but the finishing courses should be of firebrick."
3

Build the base

Build the hearth in stone up to 1 ft (30 cm) below the top, binding every course with pieces of hoop iron. Leave an arch at the back for the coal pit and the blast pipe (figs. 4, 5). Overall size is ours: fit it to your shop.

Materiais para este passo:

Bloco de pedraBloco de pedra1 peça
Arco de ferroArco de ferro1 peça
Argila refratáriaArgila refratária1 peça

Ferramentas necessárias:

Colher de pedreiroColher de pedreiro
Nível de bolhaNível de bolha
4

Make the fire back and tuyere

Bore a 3/4 in. hole through a 14-pounder iron shot and open it to a 1 in. taper on one side. Cut and countersink a hole in a 1 in. iron plate to take a third of the shot, and drill four 1/2 in. holes to bolt the plate through the wall with nuts and fish plates. (Or buy a fire back and tue-iron.)

Materiais para este passo:

Granalha de ferro (lastro)Granalha de ferro (lastro)1 peça
Placa de ferroPlaca de ferro1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados1 peça

Ferramentas necessárias:

Engenho de furarEngenho de furar
Forja de ferreiroForja de ferreiro
MarteloMartelo
5

Firebrick top and back

Lay the top courses and the back wall round the tuyere in firebrick bedded and jointed with fireclay, still binding each course with hoop iron. Build in the fire back with the shot as the tuyere, and leave a slanting flue hole just above it (fig. 5).

Materiais para este passo:

Tijolos refratáriosTijolos refratários1 peça
Argila refratáriaArgila refratária1 peça
Arco de ferroArco de ferro1 peça

Ferramentas necessárias:

Colher de pedreiroColher de pedreiro
Nível de bolhaNível de bolha
6

Fit the slake trough

Before the last course, set in a water trough 10 in. deep and wide and 22 in. long, of sheet iron, cast iron or stone, inside the rim line; bolt a sheet-iron one to the rim. A sheet-iron division riveted across gives a coal trough too.

Materiais para este passo:

Chapa de aço macioChapa de aço macio1 peça
Rebites de ferroRebites de ferro1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Engenho de furarEngenho de furar
MarteloMartelo
7

Bind with the rim

Bind the top course with a rim of 1/4 x 4 in. iron, half below the brick edge and half above it to make the hearth pan, its ends bolted to the back wall with 3/8 in. bolts built into the brickwork.

Materiais para este passo:

Placa de ferroPlaca de ferro1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados1 peça

Ferramentas necessárias:

Forja de ferreiroForja de ferreiro
BigornaBigorna
MarteloMartelo
Engenho de furarEngenho de furar
8

Connect the blast

Bring the pipe from a fan or bellows under the arch to the back of the tue-iron. He reckons about 150 cu ft (4.2 m3) of air a minute for a welding heat: a 9 in. fan at about 360 rpm or a double-action bellows.

Ferramentas necessárias:

Soprador de arSoprador de ar
9

Lay the floor

Ram wetted smiths', foundry or boiler clinkers sprinkled with a little Portland cement hard and level, with a thin layer of smithy cinder ashes beaten on top. Stone or ordinary concrete floors misbehave when hot iron is dropped on them.

Materiais para este passo:

Cimento PortlandCimento Portland1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

MarteloMartelo
10

Troubleshooting

Hearth troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" I, **Amateur Work, Illustrated**, vol. V (1886), pp. 161-162 and figs. 2, 4, 5 (checked on the archive.org scan amateurworkillus05lond). He gives no overall hearth size; that and the metric figures and tools are ours.

Materiais

11

Ferramentas necessárias

7

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...