Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Electric Kettle: Immersion Heater with a Steam and Switch-On-Dry Cut-Out (Taylor, US 4,358,666)
Ed

Criado por

Ed

9. novembro 2026FI
7
0
0
0
0

Electric Kettle: Immersion Heater with a Steam and Switch-On-Dry Cut-Out (Taylor, US 4,358,666)

An automatic electric kettle boils water with an immersion heater and switches itself off. J. C. Taylor (US 4,358,666, 1982) mounts one control on the heater's head: a bimetal disc touching the hot head cuts the power if the kettle is switched on dry, and a second bimetal disc in the steam trips an over-centre lever that cuts it when the water boils. In his kettle (Fig. 14) the steam leaves through a hole high in the wall and runs down a passage between the handle and the wall to the control. A knob resets it. Source: J. C. Taylor, US Patent 4,358,666 (filed 1980, granted 1982). Picture: its Fig. 14.
Avançado
Unknown

Instruções

1

Read Taylor

"The effect is that when the water boils, the lever 16 is tripped by the actuator 22 from its first to its second position, thus interrupting the supply of electricity to the heating element."
2

Fit the immersion heater

Make the kettle body with a spout, lid and handle, an opening low in the back wall for the heater head and a hole high in the wall under the handle for steam. Fix the immersion heater's head watertight in the low opening, with its element low in the kettle and its hot return brazed to the head so the head heats up if the element runs dry. Form a steam passage between the handle and the wall from the high hole down to the head. Body material, size and heater rating are not given.

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 kettle body
Elemento de aquecimentoElemento de aquecimento1 immersion heater

Ferramentas necessárias:

Maçarico de brasagemMaçarico de brasagem
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Método de conformação desconhecidoMétodo de conformação desconhecido
Dimensões desconhecidasDimensões desconhecidas
3

Build the switch-on-dry unit

On the head mount a switch unit with three pins (line, neutral and earth) for the kettle lead's socket. Wire the line pin to one cold end of the element through a movable contact on a springy conductive strip and a fixed contact. Rivet the tongue of a snap-acting bimetal disc to a pillar so its body touches the head. Fit a sliding link that the disc pushes: at about 120 °C (Taylor: "say 120° C.") the disc snaps over and the link parts the contacts.

Materiais para este passo:

Material isolante desconhecidoMaterial isolante desconhecido1 switch unit body
Metal desconhecidoMetal desconhecido1 pins, contacts and strip
Lâmina bimetálicaLâmina bimetálica1 dry-switch disc

Ferramentas necessárias:

Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
4

Make the steam unit

Press a disc of sheet bimetal into a domed die, with a cut-out that leaves a tongue in the middle, so it snaps over when steam heats it. Mount it by its rim on a lever that rocks on two knife edges in notches of a body seated over the switch unit, held by two over-centre C-springs, with a shroud round the pins and a steam opening sealed by an O-ring. A finger of the lever passes through the sliding link; a knob on the lever comes out through the housing. The trip temperature and bimetal grade are not given.

Materiais para este passo:

Lâmina bimetálicaLâmina bimetálica1 steam disc
Material isolante desconhecidoMaterial isolante desconhecido1 steam unit body and lever
MolaMola2 C-springs
O-ringO-ring1 peça

Ferramentas necessárias:

Método de conformação desconhecidoMétodo de conformação desconhecido
5

Close up and use

Screw the outer housing over both units into the threaded pillars, the knob through its opening and the steam passage meeting the steam unit's channel. Fill, plug in the lead and press the knob down to close the contacts. When the water boils, steam reaches the disc, the lever snaps over and the power goes off; switched on dry, the head heats and the other disc cuts it and holds the lever off. Press the knob to reset.

Materiais para este passo:

Material isolante desconhecidoMaterial isolante desconhecido1 outer housing
Cabo flexível com fichaCabo flexível com ficha1 kettle lead with socket

Materiais

7

Ferramentas necessárias

5

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...