Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Electronic Analytical Balance: a Coil Current in Place of Weights (Akers et al., 1977)
Penny

Criado por

Penny

2. novembro 2026DK
8
0
0
0
0

Electronic Analytical Balance: a Coil Current in Place of Weights (Akers et al., 1977)

The equal-arm balance with its weights replaced by electricity. The pan sits on a coil in the gap of a permanent magnet. A load pushes it down; capacitor rings sense the smallest movement, and a servo drives just enough current through the coil to lift it back to its rest position. That current is the weight. Result: a balance that reads the weight in grams or ounces on a digital display, with no weights to handle, and tare by its circuit. Source: C. B. Akers and others (Arbor Laboratories), US Patent 4,034,819 (1977). Unknown: the resolution, capacity, magnet type, materials and sizes; the circuits are given as blocks only. Picture: patent drawing.
Avançado
2 weeks

Instruções

1

Build the magnet circuit

Stack permanent magnets into a column with a soft iron core. Enclose them in an annular outer housing with end caps, shaped so the field crosses a narrow annular air gap at a constriction. Keep the whole structure symmetrical about its vertical axis. Mount it on a support plate fixed to an upright, such as a housing panel on a base. Not given: the magnet type, materials and sizes.

Materiais para este passo:

Íman pequenoÍman pequeno1 column
Vareta de ferroVareta de ferro1 soft iron core
Metal desconhecidoMetal desconhecido1 housing and end caps
Material desconhecidoMaterial desconhecido1 support plate, panel, base

Ferramentas necessárias:

Conjunto de chaves de fendasConjunto de chaves de fendas
Dimensões desconhecidasDimensões desconhecidas
2

Hang the coil in the gap

Wind the coil tightly round the middle of a light bobbin that surrounds the core, the coil sitting in the air gap. Tabs at both ends of the bobbin pass out through holes in the end caps to suspension frames. Hang the frames from thin springy cantilevers fixed to the upright, so the bobbin can only move a short way straight up and down. Keep the bobbin and its suspension as light as possible. Put the weighing pan on top. Ours: enamelled wire.

Materiais para este passo:

Fio de cobre esmaltadoFio de cobre esmaltado1 coil
Material desconhecidoMaterial desconhecido1 bobbin, frames, cantilevers
Prato de pesagemPrato de pesagem1 peça

Ferramentas necessárias:

Dimensões desconhecidasDimensões desconhecidas
3

Fit the capacitor rings

Mount four capacitor rings inside the outer housing, two above and two below the air gap, facing matching rings on the bobbin. Cross-connect them so a tilt of the bobbin cancels out and only up-and-down movement shows. Connect them to a signal generator: as the bobbin moves, one set's capacitance rises and the other's falls, and the difference becomes the control voltage.

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 rings
Circuito integradoCircuito integrado1 sensing circuit
Fio de ligaçãoFio de ligação1 peça
Fio de soldaFio de solda1 a little

Ferramentas necessárias:

Ferro de soldarFerro de soldar
4

Close the servo loop and read the current

Feed the control voltage to a d.c. servo that drives current through the coil, through a flexible lead, until the bobbin is back at its rest position. Pass that current through a large stable resistor, a thermal resistor that corrects for temperature and a calibration potentiometer: the voltage across them stands for the weight. A separate circuit (comparators, saw-tooth generator, oscillator and counter) turns it into a count read out as grams or ounces. Tare is ordinary circuit logic. Ours: a segment LCD; check with calibration weights.

Materiais para este passo:

Circuito integradoCircuito integrado1 servo and counting circuits
ResistênciaResistência2 stable resistor, thermal resistor
PotenciómetroPotenciómetro1 calibration
Visor LCD de segmentosVisor LCD de segmentos1 display
Fio de soldaFio de solda1 a little

Ferramentas necessárias:

Ferro de soldarFerro de soldar
Conjunto de pesos de calibraçãoConjunto de pesos de calibração

Materiais

12

Ferramentas necessárias

4

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...