Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Geared Crank-Frame Churn: A Frame Over an Ordinary Churn Gears a Hand Crank Up to Drive a Grated Dasher by Pitman
Buttercup

Criado por

Buttercup

11. novembro 2026IE
5
0
0
0
0

Geared Crank-Frame Churn: A Frame Over an Ordinary Churn Gears a Hand Crank Up to Drive a Grated Dasher by Pitman

J. W. Evans of Forsyth, Georgia, received US 28,462, dated 29 May 1860, for a frame on legs that stands over an ordinary churn. A hand crank turns a cogged wheel and a pinion, whose crank works a pitman and a sliding sash; the dasher is held in the sash by a set screw, so it is put in or taken out in a moment, and makes several strokes to each turn of the handle. The dasher is a grated one. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days, plus printing

Instruções

1

Several strokes to one turn

A carregar o notebook Jupyter…
2

More strokes than turns, three months before

Clement gets two strokes a turn from a toggle. Evans gears his crank up for four.
3

Read US 28,462

"The nature of my invention consists in providing a frame with suitable gearing to communicate a reciprocating motion to which the dasher of an ordinary churn can be attached or detached with facility, the whole forming a churn which can be worked to great advantage by a laborer by means of a crank."
4

Print the grated dasher h

Disc 200 mm across and 10 thick with seven slots 14 mm wide, a rim and a cross bar. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
5

Print the cogged wheel w

Spur gear, module 2.5, 48 teeth, 12 mm wide, with a hub; bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Print the pinion p

Spur pinion, module 2.5, 12 teeth, 12 mm wide, with a hub; bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
7

Frame A and legs L

From pine lumber 40 x 80 mm cut two uprights 570 mm long and a top bar 380 long, and join them 300 mm apart inside. Rout a groove 12 x 42 mm down the inside of each upright for the sash. Stand the frame on two rails and four legs 400 tall, the rails across the bucket's place so the frame stands over it. Screw a hardwood strap 60 x 20 mm upright behind the frame's middle, with a cross piece near its foot, and bore it 16.6 mm for the shafts c and d, 75 mm apart, 400 and 475 mm above the frame's foot.

Materiais para este passo:

Madeira de pinhoMadeira de pinho3 peças
Tábua de madeira de leiTábua de madeira de lei1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira30 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
TupiaTupia
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
8

Wheel w, pinion p, cranks k and d

Pass a 16 mm stainless shaft c through the upper hole with the wheel w on its front end and a hardwood crank k 140 mm long with a dowel handle on its back end. Pass a short 16 mm shaft through the lower hole with the pinion p meshing w, and in front of it a hardwood crank d with a 12 mm stainless pin 40 mm from the shaft. Hold both with collars.

Materiais para este passo:

Varão de aço inoxidávelVarão de aço inoxidável2 peças
Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Shaft CollarShaft Collar4 peças
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
LixaLixa
9

Pitman e, sash f and set screw i

Cut a hardwood pitman 20 x 10 mm with 12.6 mm holes 220 mm apart. Cut a hardwood sash 320 x 40 x 40 mm with tongues on its ends to slide in the grooves; bore it 22.6 mm through the middle for the dasher rod, slot its front for the pitman, and pin the pitman in the slot. Drill and tap a hole through the sash's back into the bore, or set a nut in it, and run in a short piece of threaded rod with a wing nut as the set screw i.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
ContrapinoContrapino2 peças
Varão roscadoVarão roscado1 peça
Porca sextavadaPorca sextavada1 peça
Porca borboletaPorca borboleta1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Serra de arco para metaisSerra de arco para metais
Chave inglesa ajustávelChave inglesa ajustável
10

Dasher g with the grate h

Glue a 22 mm hardwood dowel 555 mm long into the printed grate's centre, and cut a 28 mm hole in the centre of the bucket's lid for it.

Materiais para este passo:

Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Balde de 20 litrosBalde de 20 litros1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
11

The build in 3D

FreeCAD model of this build, the bucket cut open: the frame on its legs, the wheel w and pinion p behind the crank d, the pitman and the sash in its grooves, the dasher held by the set screw, and the grated dasher near the bucket's floor.
Arquivo de designBLENDCC0 - Free
12

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket and put on the lid. Stand the frame over it, pass the dasher down through the sash into the bucket, set it so it just clears the floor at the bottom of the stroke and tighten the set screw. Turn the crank k steadily, timing it. When the butter comes, loosen the set screw and lift the dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater8 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
13

Troubleshooting

Geared crank-frame churn troubleshooting.

Flow

Loading...
14

History and honest limits

**J. W. Evans** of Forsyth, Monroe County, Georgia, US 28,462, 29 May 1860, "Churn". He did not claim churn dashers worked by a crank nor the grated dasher, "as they are old and well known", but the arrangement with the grated dasher, sash and set screw. His frame is arched and on curved legs, and his wheel and pinion are drawn face-toothed; ours are spur gears on a strap behind a straight frame. Every size is ours.

Materiais

16

Ferramentas necessárias

19

Ficheiros de design

4

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...