Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
New Year Noisemaker: a Spun Box Whose Wooden Tongues Clack Over a Pinned Bobbin (Folkush, 1921)
Woody

Criado por

Woody

13. novembro 2026NO
8
0
0
0
0

New Year Noisemaker: a Spun Box Whose Wooden Tongues Clack Over a Pinned Bobbin (Folkush, 1921)

Martin Folkush of Milwaukee received US 1,374,644, dated 12 April 1921, for a noisemaker "that can be heard for a great distance". Hold the handle and swing the box round it: two thin wooden tongues inside snap over the posts of a fixed bobbin, one in single clacks and one in double, and the box rings like a sounding board. A slider changes the pitch. We make it from plywood, dowel and hardwood strip. All sizes are ours.
Intermediário
About 4 hours

Instruções

1

Posts on the bobbin

A carregar o notebook Jupyter…
2

Read US 1,374,644

"Upon rotating the casing 12 upon the shaft 11, the sounding boards 21 and 22 will be brought into violent engagement with the posts 19 and 20 causing loud sounds to be emitted."
3

Make the handle and shaft

Shape a handle from hardwood handle stock with a rasp, his handle 10, and glue a dowel shaft 11 into its end.

Materiais para este passo:

Barrote de madeira dura para cabosBarrote de madeira dura para cabos1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Grosa para madeiraGrosa para madeira
LixaLixa
Berbequim de mãoBerbequim de mão
4

Make the bobbin

Cut three plywood disks 60 mm across (ours): two ends and the middle disk 18. Drill all three on the circle from the notebook and glue dowel posts 19 through all of them; then glue the shorter posts 20 between the middle disk and one end disk only, between the long ones. Drill the centre for the shaft and pin the bobbin to it, his pin 17.

Materiais para este passo:

Placa de contraplacadoPlaca de contraplacado1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
PregosPregos1 peça

Ferramentas necessárias:

Serra de recortesSerra de recortes
Compasso de pontasCompasso de pontas
Berbequim de mãoBerbequim de mão
SerroteSerrote
5

Make the casing

Cut two plywood sides 14 with a round head 13 at one end, bored for the shaft. Join them with a closed end 24 and an open frame so the bobbin turns freely between the heads. Glue a cross rib 23 inside the closed end. Cut a slot 28 in each side for the slider.

Materiais para este passo:

Placa de contraplacadoPlaca de contraplacado1 peça
Cola de madeiraCola de madeira1 peça
PregosPregos1 peça

Ferramentas necessárias:

SerroteSerrote
Serra de recortesSerra de recortes
Berbequim de mãoBerbequim de mão
6

Fit the sounding boards

Cut two thin hardwood strips (his sounding boards 21 and 22) long enough to reach from the rib to just inside the circle of posts, and screw their ends to the rib, side by side, one opposite each half of the bobbin.

Materiais para este passo:

Ripa de madeira duraRipa de madeira dura1 peça
Parafusos para madeiraParafusos para madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Berbequim de mãoBerbequim de mão
Conjunto de chaves de fendasConjunto de chaves de fendas
7

Fit the slider and close the box

Make a small wooden slider 26 that surrounds both boards, with a length of threaded rod through it whose ends pass out through the slots; put a wing nut on each end (his set nuts 29). Put the casing on the shaft over the bobbin and close the other side with a plywood plate 25, making a resonant box.

Materiais para este passo:

Ripa de madeira duraRipa de madeira dura1 peça
Varão roscadoVarão roscado1 peça
Porca borboletaPorca borboleta2 peças
Placa de contraplacadoPlaca de contraplacado1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Berbequim de mãoBerbequim de mão
Serra de arco para metaisSerra de arco para metais
8

Play it

Hold the handle and swing the box round the shaft: the boards snap over the posts. Slide the slider toward the bobbin for a higher, sharper sound, away for a deeper one, and lock it with the wing nuts.
9

Troubleshooting

Noisemaker troubleshooting.

Flow

Loading...
10

History and honest limits

**Martin Folkush** of Milwaukee, US 1,374,644, dated 12 April 1921, filed 10 April 1920. He claimed "a noise maker comprising a shaft, a casing journaled thereon, a frame having spaced end supported posts", "one half of said frame being provided with double the number of posts that the other half has", and the pitch-adjusting slider. He names no materials and gives no sizes: the wood, all sizes, wing nuts and threaded rod are ours.

Materiais

9

Ferramentas necessárias

8

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...