Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Fused Quartz Tube: Blown from Brazil Pebble in the Oxy-Gas Flame (Shenstone, 1916)
Charlie

Criado por

Charlie

4. novembro 2026DE
15
0
0
0
0

Fused Quartz Tube: Blown from Brazil Pebble in the Oxy-Gas Flame (Shenstone, 1916)

Fused silica stands sudden heating and cooling that would crack glass, but natural quartz splinters violently in a flame. W. A. Shenstone, in The Methods of Glass-Blowing and of Working Silica in the Oxy-Gas Flame (1916), first turns Brazil pebble into a "non-splintering" silica by quenching it from a yellow-red heat, then melts it in an oxy-gas flame into fine rods, wraps the rods round a platinum core into a first tube, and enlarges it with rings of rod blown out. Not given: quantities and times. He advises most workers to start from bought tubes and to learn each stage by practice. Source: W. A. Shenstone (1916), pp. 88-94. Picture: his p. 93.
Avançado
Several days of practice

Instruções

1

Read Shenstone

"The silica tubes thus made can be cut and broken like glass, they can be joined together before the flame, and they can also be drawn into smaller tubes when softened by heat."
2

Crack the Brazil pebble

Clean the chips of Brazil pebble (rock crystal) thoroughly, heat them in boiling water and drop them into cold water. Repeat until they have cracked enough to break easily with a clean steel pestle or hammer. Hand-pick the fragments and reject any that are not perfectly free from foreign matter.

Materiais para este passo:

Cristal de rochaCristal de rocha1 as required
ÁguaÁgua1 as required

Ferramentas necessárias:

Tacho altoTacho alto
Placa de aquecimentoPlaca de aquecimento
BaldeBalde
Martelo de bolaMartelo de bola
3

Make it non-splintering

Heat the pure, transparent pieces to a yellow-red heat in a covered platinum dish in a muffle furnace and plunge them quickly into a deep clean vessel of distilled water. Repeat until they are semi-opaque, friable masses like white enamel. Wash them with distilled water, drain and dry. Now they can go straight into the hottest part of the flame without splintering.

Materiais para este passo:

Água destiladaÁgua destilada1 as required

Ferramentas necessárias:

Cápsula de platinaCápsula de platina
Forno muflaForno mufla
Tenaz para cadinhoTenaz para cadinho
Copo de vidro (gobelé)Copo de vidro (gobelé)
4

Set up the flame

Use an efficient oxy-gas burner fed with coal gas and oxygen from a bottle fitted with a gauge and regulator; watch the oxygen used. Protect your eyes with very dark glasses, so dark that work is a little difficult at first, and keep a second pair for long spells, as the glasses get hot. The hottest spot is near the tip of the inner cone: bring the work exactly there.

Materiais para este passo:

Gás de hulhaGás de hulha1 as required
OxigénioOxigénio1 as required

Ferramentas necessárias:

Maçarico de oxigénio e gás de iluminaçãoMaçarico de oxigénio e gás de iluminação
Garrafa de gás sob pressãoGarrafa de gás sob pressão
Redutor de pressãoRedutor de pressão
ManómetroManómetro
Óculos escuros de forjaÓculos escuros de forja
5

Draw fine rods

Hold a fragment in platinum-tipped forceps and melt one corner. Press a second fragment against the melted part until they stick, and heat from below upwards (to avoid bubbles) until it is clear. Add a third, a fourth and so on until you have an irregular rod. Reheat it in sections and draw it out into rods or coarse threads 1 to 2 mm across.

Ferramentas necessárias:

Pinça com pontas de platinaPinça com pontas de platina
Maçarico de oxigénio e gás de iluminaçãoMaçarico de oxigénio e gás de iluminação
Óculos escuros de forjaÓculos escuros de forja
6

Make the first tube

Bind a few rods round a platinum rod about 1 mm across with platinum wires at both ends. Withdraw the core slightly from one end and heat gradually from there until a rough tube 4 to 5 cm long has formed. Close one end, blow it into a small bulb, fix a silica rod to the far end of the bulb, reheat and draw it out into a fine tube. Blow a fresh bulb on one end and draw it out again, until the tube is 6 to 8 cm long.

Ferramentas necessárias:

Fio de platinaFio de platina
Pinça com pontas de platinaPinça com pontas de platina
Maçarico de oxigénio e gás de iluminaçãoMaçarico de oxigénio e gás de iluminação
Óculos escuros de forjaÓculos escuros de forja
7

Blow without soiling it

Blow through a rubber tube on the open end of the silica tube, with a glass tube loosely packed with granulated potash between your mouth and the work so the inside stays clean. Do not take a hot bulb out of the flame to blow it; move it just off the hot spot. Mend holes with plastic silica from the softened end of a fine rod and blow the lump out. Keep the silica clean: a white crust that forms is removed by reheating, but dust or handling can spoil the surface for good.

Ferramentas necessárias:

Tubo de borrachaTubo de borracha
Tubo de vidroTubo de vidro
Carbonato de potássio (potassa)Carbonato de potássio (potassa)
Maçarico de oxigénio e gás de iluminaçãoMaçarico de oxigénio e gás de iluminação
8

Enlarge and lengthen

To widen a bulb into a tube, lay a ring of fine rod round its end, heat the ring and the end until soft and blow; repeat until the bulb becomes a short tube. For a long tube make several pieces 200 to 250 mm long at the diameter you need and join them end to end. Thicken a tube by adding rings and blowing them out. For a large tube, set a plate of silica behind the work to throw the flame back onto its far side.

Ferramentas necessárias:

Maçarico de oxigénio e gás de iluminaçãoMaçarico de oxigénio e gás de iluminação
Pinça com pontas de platinaPinça com pontas de platina
Óculos escuros de forjaÓculos escuros de forja
9

History and honest limits

Thorpe's Dictionary (vol. IV, 1913) records Gaudin spinning fused silica threads in 1839, Boys making quartz fibres in 1887, and Shenstone showing in 1901 how to make tubes and bulbs before the oxy-coal-gas blowpipe. Shenstone gives no quantities or times and says most workers save time and money by starting from bought silica tubes. A finished tube holds a little moisture and nitric peroxide; he removes them by heating it and drawing filtered air through, not by washing.

Materiais

5
  • 1 as required
    Referência
  • 1 as required
    Referência
  • 1 as required
    Referência
  • 1 as required
    Referência
  • 1 as required
    Referência

Ferramentas necessárias

18

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...