Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Gasholder: Water-Sealed Zinc Gasometer with Balance Weights (Ramsay & Travers, 1898)
The laboratory gasometer Ramsay and Travers used to store argon: a zinc bell that rises and falls in a narrow ring of water between two fixed zinc cylinders. Because the water space is only about 2 cm wide, little gas dissolves in it. Weights on cords over pulleys balance the bell, and weights laid on top push the gas out.
Result: a water-sealed gasholder of 18 to 180 litres.
Source: M. W. Travers, The Experimental Study of Gases (1901), pp. 30 and 105-106. Unknown: sizes and how the zinc is joined. Picture: Fig. 34, the small mercury form of the same design.
Intermediário
Unknown
Instruções
1
1
Make the fixed cylinders
Make the fixed cylinders
Make two concentric zinc cylinders on a closed base, leaving a ring-shaped space about 2 cm wide between them for the water. Make the top of the inner cylinder dome-shaped. Bring a gas pipe with a stopcock up through the inner cylinder. Ours: zinc soldered with tin-lead solder. Not given: sizes, how the zinc is joined, the stopcock.
Materiais para este passo:
Chapa de zinco1 outer and inner cylinders, base
Solda de estanho-chumbo1 seams
Válvula desconhecida1 gas stopcockFerramentas necessárias:
Tesoura de chapa
Ferro de soldar
Método de conformação desconhecido
Dimensões desconhecidas2
2
Make and hang the bell
Make and hang the bell
Make the gasholder bell of zinc to fit closely over the inner cylinder and down into the water ring, with a dome-shaped top matching the inner cylinder's, so all the gas can be pushed out. Ramsay and Travers made bells of about 180, 27, 18 and 18 litres. Tie a cord to the top of the bell and pass it over pulleys to a hanging weight, to take the bell's own weight off the gas. Fill the ring with water. To deliver gas, take weight off the cord or lay weights on top of the bell. Not given: the weights.
Materiais para este passo:
Chapa de zinco1 bell
Solda de estanho-chumbo1 seams
Cordel de cânhamo1 balance cords
Roldana2 pulleys
Metal desconhecido1 balance weightsFerramentas necessárias:
Tesoura de chapa
Ferro de soldarMateriais
6- 1 bellReferência
- 2 seamsReferência
- 1 gas stopcockReferência
- 1 balance cordsReferência
- 2 pulleysReferência
- 1 balance weightsReferência
Ferramentas necessárias
4- Referência
- 2 vendors sell this, none ship to you yetReferência
- Referência
- Referência
Materiais de Blueprints conectados

10% de atribuição
Zinc Sheet Cast as a Plate and Hammered Warm
por Forge
Trabalho em Metal
23
0
0
0
1
0

Perigoso
10% de atribuição
Making Tin-Lead Solder — The Ancient Alloy That Joins Metals Without a Forge
por Peter
Trabalho em Metal
62
0
0
0
3
0

10% de atribuição
Hand-Spun Three-Ply Hemp Cord
por Tex
Têxtil e Couro
43
0
0
0
1
0
Este projeto faz
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.
