Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)
Forge

Criado por

Forge

13. novembro 2026NO
9
0
0
0
0

Rotary Lawn Sprinkler: a Barker's-Mill Head Turning on Balls Round the Supply Pipe (Gibbs, 1901)

Henry Gibbs of Chicago received US 683,645, dated 1 October 1901, for a lawn sprinkler "operating on the familiar Barker's mill principle": water leaving its arms sideways pushes the head round. His head turns on a ring of steel balls held in matching grooves in the head and in the end of the supply pipe, so it spins freely with little friction and stays on. We turn the head from brass and the groove in a steel pipe on the lathe. All sizes are ours.
Intermediário
About 5 hours

Instruções

1

How many balls

A carregar o notebook Jupyter…
2

Read US 683,645

"It being only necessary that certain of the orifices shall discharge the water tangentially to revolve the head 14 and spray-pipes 15 in the well-known manner."
3

Groove the supply pipe

Chuck a length of steel pipe (his pipe 13) and finish its top end smooth and round. Cut a half-round groove (his 17) round it a little below the end, to the depth the notebook gives, with a round-nosed tool. Use thick-walled pipe, so at least 1.5 mm of wall is left under the groove (ours).

Materiais para este passo:

Tubo de aço (de parede grossa, com roscas)Tubo de aço (de parede grossa, com roscas)1 peça

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
4

Turn the head

Turn a brass bar to a short round head (his 14). Bore it from below to loosely fit the pipe end, his bore 16, but stop short of the top so a lip (his flange 22) overhangs the pipe end. Cut a matching groove 18 inside the bore at the same height as the pipe's groove.

Materiais para este passo:

Barra redonda de latãoBarra redonda de latão1 peça

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Conjunto de brocas de centrarConjunto de brocas de centrar
Jogo de brocasJogo de brocas
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
5

Drill the ball hole and the arms

Drill a hole (his opening 20) through the head's side into the groove, just bigger than a ball, and tap it for a screw plug (21). Drill three holes round the head into the bore for the spray pipes.

Ferramentas necessárias:

Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Jogo de machos e cossinetesJogo de machos e cossinetes
Torno de bancadaTorno de bancada
6

Make the spray pipes

Cut three lengths of copper tube, close their outer ends, and bend the last bit of each upward as his Fig. 1. Drill small holes near the ends, some pointing sideways (tangentially), all the same way round, so the jets turn the head. Solder the pipes into the head's holes (ours; he threads them in).

Materiais para este passo:

Tubo de cobreTubo de cobre1 peça
Solda de estanho-chumboSolda de estanho-chumbo1 peça
FluxoFluxo1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de brocasJogo de brocas
Engenho de furarEngenho de furar
Ferro de solda elétricoFerro de solda elétrico
Torno de bancadaTorno de bancada
7

Assemble with the balls

Slide the head onto the pipe end with the grooves level. Feed balls in through the side hole, turning the head, until the race is full; then screw in the plug. The head should spin freely and not lift off.

Materiais para este passo:

Rolamentos de esferas de açoRolamentos de esferas de aço1 peça
Parafusos de máquinaParafusos de máquina1 peça

Ferramentas necessárias:

Chave inglesa ajustávelChave inglesa ajustável
8

Make the stand

Bore a hardwood block to hold the pipe upright and glue in three splayed dowel legs (ours; his base 10 and supports 11). Screw the hose coupling onto the pipe's lower end below the block (his coupling 12).

Materiais para este passo:

Bloco de madeira duraBloco de madeira dura1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Engate de mangueiraEngate de mangueira1 peça

Ferramentas necessárias:

SerroteSerrote
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
9

Run it

Connect a garden hose and turn on the water slowly: the jets push the head round and throw the water in a circle. More pressure turns it faster.
10

Troubleshooting

Lawn sprinkler troubleshooting.

Flow

Loading...
11

History and honest limits

**Henry Gibbs** of Chicago, assignor to W. D. Allen Manufacturing Company, US 683,645, dated 1 October 1901, filed 20 May 1901. He claimed a single-piece hollow coupling with radial spray pipes having tangential orifices, a bore loosely fitting the supply pipe, "annular grooves in the opposed cylindrical faces of said bore and said pipe" and "bearing balls interposed in said grooves". He gives no sizes or metals; the brass, steel pipe, ball size, soldered copper arms and the wooden stand are ours.

Materiais

11

Ferramentas necessárias

13

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...