Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)
Forge

Criado por

Forge

13. novembro 2026NO
6
0
0
0
0

Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)

Charles Gottschalk of St. Paul, Minnesota, received US 1,584,028, dated 11 May 1926, for a table saw with two saws. A crosscut saw and a rip saw stand at opposite corners of one table, so either or both can be used without changing blades. An electric motor inside the frame drives both through two chains. The top is hinged twice and lifted by a hand screw at either end, which sets each saw's depth of cut on its own. A lever with wheels lets two people truck the whole machine about. The patent gives no sizes; every size here is ours.
Avançado
About 1 week

Instruções

1

Setting each saw's depth

A carregar o notebook Jupyter…
2

Read US 1,584,028

"Inasmuch as the saws are positioned fairly close to the hinges 19 and 23 the movement of the table for one of the saws does not appreciably affect the positioning of the same in regard to the other saw so that the depth of cut of either of the two saws may be adjusted independently or simultaneously if desired."
3

Frame on skids

From 45 x 95 mm pine: two skids 10, 11 1200 mm long; four uprights 12 775 mm long; two top rails 13 1300 mm long, their ends 50 mm past the uprights (17 at the rear, 18 at the front); cross rails 14, 15 between the uprights; a motor bed 52 across the skids. Glue and bolt the joints with carriage bolts, square and level, so the rails' tops stand 820 mm above the floor and 600 mm apart.

Materiais para este passo:

Madeira de pinhoMadeira de pinho10 peças
Parafuso de carroçariaParafuso de carroçaria24 peças
Anilha planaAnilha plana24 peças
Porca sextavadaPorca sextavada24 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Chave inglesa ajustávelChave inglesa ajustável
Sargento de barraSargento de barra
Esquadro combinadoEsquadro combinado
Fita métricaFita métrica
4

Turn the two arbors

From 30 mm steel bar turn two arbors 26, 27, each 400 mm long. On one end of each turn a collar 40 mm across and 6 mm thick 30 mm from the end, and screw-cut the last 25 mm M20 on the lathe; turn a loose flange 60 mm across with a 20 mm bore for each. Drill and tap the sprockets' hubs for set screws if they have none.

Materiais para este passo:

Barra redonda de aço macioBarra redonda de aço macio2 peças
Porca sextavadaPorca sextavada4 peças

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
Serra de arco para metaisSerra de arco para metais
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Jogo de machos e cossinetesJogo de machos e cossinetes
Desandador de machosDesandador de machos
Óculos de segurançaÓculos de segurança
5

Mount the arbors and the saws

Bolt two 30 mm flange bearings 28 to the outsides of the rails for each arbor, its centre 30 mm below the rails' tops: the crosscut saw's arbor 27 250 mm from the front ends, the rip saw's arbor 26 250 mm from the rear ends. Push the arbors through so the crosscut saw's threaded end stands out past the left rail and the rip saw's past the right one, seen from the front. Fix a 17-tooth #40 sprocket on each arbor between the rails. Put each 250 mm blade on its collar, the teeth at the top pointing to the front, then the loose flange, a nut and a second nut locked against it.

Materiais para este passo:

Mancal de flangeMancal de flange4 peças
Roda dentadaRoda dentada2 peças
Circular Saw Blade SetCircular Saw Blade Set1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados16 peças
Parafuso sem cabeça de ponta côncavaParafuso sem cabeça de ponta côncava4 peças

Ferramentas necessárias:

Chave inglesa ajustávelChave inglesa ajustável
Jogo de chaves AllenJogo de chaves Allen
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
6

Motor and chains

Bolt the motor 51 to its bed between the skids under the arbors, its shaft parallel to them, and fit two 17-tooth sprockets 52 on its shaft, each in line with one arbor's sprocket. Fit a #40 chain 53, 54 from each to its arbor, tensioned by sliding the motor in slotted bolt holes. Have the motor wired to a switch within reach at the front. Oil the chains.

Materiais para este passo:

Motor elétricoMotor elétrico1 peça
Roda dentadaRoda dentada2 peças
Corrente de rolosCorrente de rolos2 peças
Interruptor de ligar/desligarInterruptor de ligar/desligar1 peça
Óleo de máquinaÓleo de máquina1 peça

Ferramentas necessárias:

Chave inglesa ajustávelChave inglesa ajustável
Jogo de chaves AllenJogo de chaves Allen
7

The hinged members and the top

Cut two hardwood members 20, 21 20 x 70 mm, 1340 mm long, to lie flat on the rails; hinge their front ends to the rails' front ends 19 and let them reach 40 mm past the rear 22. Cut the 18 mm plywood top 24 1400 x 800, with a slot over each blade, and hinge its rear edge to the members' rear ends 23. Rout a square groove 35 for the crosscut guide parallel to the crosscut saw and a second groove 200 on its other side, and a groove 42 across the top for the rip guide's bar.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Placa de contraplacadoPlaca de contraplacado1 peça
Dobradiça de livroDobradiça de livro4 peças
Parafusos para madeiraParafusos para madeira40 peças

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
TupiaTupia
Conjunto de fresas de tupiaConjunto de fresas de tupia
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Esquadro combinadoEsquadro combinado
Fita métricaFita métrica
8

The depth screws

Screw a 6 mm steel plate under each rail's projecting end, drilled and tapped M12. Run a 150 mm M12 threaded rod up through each, with a wing nut locked on its lower end as a handle. The rear pair 156 push up under the members' rear ends 22, lifting members and top on the front hinges 19: this sets the rip saw. The front pair 157 pass through holes 58 in the members and push the top alone up on its rear hinges 23: this sets the crosscut saw.

Materiais para este passo:

Barra chata de aço macioBarra chata de aço macio1 peça
Varão roscadoVarão roscado4 peças
Porca borboletaPorca borboleta4 peças
Porca sextavadaPorca sextavada4 peças
Parafusos para madeiraParafusos para madeira16 peças

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Jogo de machos e cossinetesJogo de machos e cossinetes
Desandador de machosDesandador de machos
Chave inglesa ajustávelChave inglesa ajustável
9

The guides

Crosscut guide: a hardwood bar 39 sliding in groove 35, with an angle fence 37 pivoted on it at 36 and clamped at any angle by a wing nut 40 through an arc slot 38. Rip guide: a bar 43 sliding in groove 42, held by a hand screw 49 through a plate 50, carrying a fence 45 hinged on a bracket 44 and tilted by a wing nut 67 in an arc slot 47.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Parafuso de carroçariaParafuso de carroçaria4 peças
Porca borboletaPorca borboleta3 peças
Barra chata de aço macioBarra chata de aço macio1 peça

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Esquadro combinadoEsquadro combinado
10

The truck

Pivot two hardwood arms 60, 61 to the rear ends of the skids at 66, with a wheel 62 on the end of each beyond the pivot. Their front ends 63 are handles sliding in keepers 64 on the front uprights. With the handles down, the wheels are off the floor; lift the handles and the wheels take the weight so the saw can be wheeled away.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Conjunto de rodas de borrachaConjunto de rodas de borracha1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados4 peças
Parafusos para madeiraParafusos para madeira8 peças

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Chave inglesa ajustávelChave inglesa ajustável
11

Try it

Wind both screw pairs down and check each blade stands square to the top and parallel to its groove. Set the rip saw's depth with the rear screws and the crosscut's with the front screws, each about 10 mm above the wood. Wearing glasses and ear defenders, rip a board along the rip guide, then cut the end off another against the crosscut guide.

Ferramentas necessárias:

Esquadro combinadoEsquadro combinado
Fita métricaFita métrica
Óculos de segurançaÓculos de segurança
Proteção auditiva (abafadores, SNR 30 dB)Proteção auditiva (abafadores, SNR 30 dB)
12

Troubleshooting

Twin-saw table troubleshooting.

Flow

Loading...
13

History and honest limits

**Charles Gottschalk** of St. Paul, Minnesota, US 1,584,028, dated 11 May 1926, filed 1 August 1921. He claimed a frame with two rails, longitudinal members hinged to the rails at one end, a single top hinged to them at the other, a crosscut saw at one end and a rip saw at the other through the top, and means to oscillate the members and top together, and the top alone, "so as to vary the relative depth of cut of either of said saws". He says a gasoline engine may drive it instead of the motor. His grooves are dovetailed; ours are square. He gives no sizes, speeds or sprocket sizes; all of those are ours.

Materiais

23

Ferramentas necessárias

21

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...