Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Four-Crank Gyrating Churn: Four Cranks Carry the Tub Round a Small Circle With No Dasher
Martin

Criado por

Martin

10. novembro 2026NO
8
0
0
0
0

Four-Crank Gyrating Churn: Four Cranks Carry the Tub Round a Small Circle With No Dasher

Alfred Guthrie of Chicago received US 24,907, dated 26 July 1859, for a churn with no dasher at all. Four upright shafts in a frame have cranks on their tops, and a bed plate lies over the four crank pins, so each crank turns on its own centre but all move together. The tub stands on the plate, held by stirrups, and is carried round a small circle, throwing the cream against its sides. A handle turns one crank shaft through cogged gearing. This rung builds it at the patent's own sizes: a frame about two feet square and one foot high, shafts of 3/4 inch iron and 3 inch cranks.
Intermediário
About 2 days, plus printing

Instruções

1

How hard the cream is swung

A carregar o notebook Jupyter…
2

A churn with a dasher, before it

Wineman's dasher drove the cream through holes. Guthrie did away with the dasher and moved the whole tub.
3

Read US 24,907

"I connect the whole together by the bed plate D over the wrists of each crank E, E, E, E. Each crank will revolve upon its own center but will each correspond to the motion of the other."
4

Print the wheel H

The 64-tooth spur wheel (module 3, 198 mm across) for the handle shaft I, with a 20 mm bore. PETG, 0.2 mm layers, 50 % infill, 5 walls.
Arquivo de designSTLCC0 - Free
5

Print the pinion H

The 24-tooth spur pinion for the driven crank shaft, with a 19 mm bore and a hub. PETG, 0.2 mm layers, 50 % infill, 5 walls.
Arquivo de designSTLCC0 - Free
6

Frame and bearing bars

Build a pine frame 610 mm square and 305 mm high: four 50 mm corner posts, and 50 mm rails round the top and the bottom. Fit two hardwood bars across it, top and bottom, 150 mm in front of and behind the middle, and bore them 19.6 mm square to the frame at 200 mm either side of the middle, for the four shafts. Screw two hardwood brackets to the right side, top and bottom, bored 20.6 mm 132 mm out from the front right shaft, for the handle shaft.

Materiais para este passo:

Tábua de pinhoTábua de pinho2 peças
Madeira macia de 70x70 mmMadeira macia de 70x70 mm2 peças
Tábua de madeira de leiTábua de madeira de lei2 peças
Parafuso para madeira n.º 10 x 3"Parafuso para madeira n.º 10 x 3"24 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Berbequim sem fiosBerbequim sem fios
Conjunto de brocas de páConjunto de brocas de pá
Esquadro fixoEsquadro fixo
Nível de bolhaNível de bolha
Fita métricaFita métrica
7

Shafts, cranks and plate D

Cut four 19 mm steel shafts 323 mm long and stand them in the bars. Make four hardwood crank arms, 76 mm from the shaft to the crank pin, and pin them on the shafts' tops all pointing the same way. Fit a 19 mm steel crank pin 50 mm long in each. Cut plate D 532 mm across from plywood, bore it for the four pins exactly where they stand, and drop it on them. Turn one crank by hand: the plate must run round freely without turning.

Materiais para este passo:

Barra de aço em brutoBarra de aço em bruto2 peças
Tábua de madeira de leiTábua de madeira de lei1 peça
Placa de contraplacadoPlaca de contraplacado1 peça
Anilha planaAnilha plana8 peças
Sortido de parafusos sextavadosSortido de parafusos sextavados4 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon4 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra tico-ticoSerra tico-tico
Fita métricaFita métrica
Chave inglesa ajustávelChave inglesa ajustável
8

Gearing H and handle I

Pin the pinion on the front right shaft 140 mm up. Stand a 20 mm steel shaft 885 mm long in the brackets, pin the wheel on it level with the pinion, and check they mesh fully. Fix a hardwood handle arm 150 mm long on the shaft's top with a dowel grip.

Materiais para este passo:

Filamento PETGFilamento PETG1 peça
Barra de aço em brutoBarra de aço em bruto1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de arco para metaisSerra de arco para metais
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
9

Tub F on its grooved bottom

Glue a plywood ring to the plate's middle, 282 mm inside and 340 mm outside, so the bucket's foot sits in it. Bend two flat-bar stirrups to go up the bucket's sides and over its lid, notch the ring for them and bolt them to the plate.

Materiais para este passo:

Placa de contraplacadoPlaca de contraplacado1 peça
Cola de madeiraCola de madeira1 peça
Barra chata de aço macioBarra chata de aço macio2 peças
Sortido de parafusos sextavadosSortido de parafusos sextavados4 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon4 peças
Balde de 20 litrosBalde de 20 litros1 peça

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
Torno de bancadaTorno de bancada
Serra de arco para metaisSerra de arco para metais
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Chave inglesa ajustávelChave inglesa ajustável
10

The build in 3D

FreeCAD model of this build: the frame with its bearing bars, the four shafts and cranks, plate D on the crank pins, the bucket in its ring under two stirrups, and the spur wheel on the handle shaft driving the pinion. It was checked at eight crank angles.
Arquivo de designBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, put the lid on and tighten the stirrups. Turn the handle steadily and time it. When the butter comes, lift the bucket off, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater8 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
12

Troubleshooting

Four-crank churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Alfred Guthrie** of Chicago, Illinois, assignor to Wardell Guthrie, US 24,907, 26 July 1859, "Churn". He claimed the cranks C connected by the plate D. His sizes are kept: a frame about two feet square and one foot high, shafts of 3/4 inch iron about a foot long, and cranks of 3 inches, which we read from "about a six inch throw or three inches" and Fig. 3's "3 in" marks. He gives no gear sizes; ours are printed spur gears placed as his Figs. 2-3 draw them. Every other size is ours.

Materiais

17

Ferramentas necessárias

17

Ficheiros de design

3

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...