Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Hackle Combs: Coarse and Fine Flax Heckles on One Board (Ure, 1839)
Woody

Criado por

Woody

4. novembro 2026NO
12
0
0
0
0

Hackle Combs: Coarse and Fine Flax Heckles on One Board (Ure, 1839)

A pair of flax heckles on one oblong plank: two round wooden blocks, each faced with a drilled brass or iron plate holding upright iron teeth. Flax is drawn first through the coarse heckle, then through the fine one, splitting the fibres, combing out the short tow and laying the long fibres straight. Coarse: teeth about 1/10 in thick and 1 1/4 in long, a centre tooth and 12 rings, the outer ring 5 3/4 in across. Fine: thinner teeth set closer, 1109 of them. Source: Andrew Ure, Dictionary of Arts, Manufactures and Mines (1839), 'Flax'. Picture: Figs. 424-425 of the book.
Intermediário
Unknown

Instruções

1

Make the board and blocks

Cut an oblong plank (Fig. 424, a b) and two round (or square) wooden blocks, c for the coarse heckle and d for the fine, and fix the blocks on the plank (Fig. 425). The heckles can also be made on separate boards.

Materiais para este passo:

Prancha de madeira duraPrancha de madeira dura1 peça
Bloco de madeira duraBloco de madeira dura2 peças
Parafusos para madeiraParafusos para madeira1 peça

Ferramentas necessárias:

Serrote de costasSerrote de costas
Chave de fendasChave de fendas
2

Drill the face plates

Cover the top of each block with a brass or iron plate drilled for the teeth, which gives them a firmer hold. Set the holes evenly over the whole face, in concentric circles (the German way) or parallel rows (the English way). Coarse: a centre hole and 12 rings, the outermost 5 3/4 in across. Fine: thinner holes set closer, 1109 in all.

Materiais para este passo:

Chapa de latãoChapa de latão2 face plates

Ferramentas necessárias:

Compasso de pontasCompasso de pontas
Tesoura de chapaTesoura de chapa
Berbequim de mãoBerbequim de mão
3

Make the teeth

Cut teeth of iron (sometimes steel) 1 to 2 in long. For the coarse heckle make them about 1/10 in thick and 1 1/4 in long, tapering from the middle to a very fine point; the fine heckle's teeth are thinner. File every point sharp and smooth, running evenly into the round stem like a sewing needle; square points in a rhombus shape cut the fibres apart better than round ones.

Materiais para este passo:

Arame de ferroArame de ferro1 teeth

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Lima para metalLima para metal
4

Set the teeth

Drive each tooth through its hole in the plate into the block so it stands upright, all points at one level.

Ferramentas necessárias:

MarteloMartelo

Materiais

5

Ferramentas necessárias

7

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...