Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Hand Drill: Double-Acting Push Drill, Spiral Rod and Ratchet Bevel Gears (Olson, US 652,137, 1900)
Forge

Criado por

Forge

3. novembro 2026NO
11
0
0
0
0

Hand Drill: Double-Acting Push Drill, Spiral Rod and Ratchet Bevel Gears (Olson, US 652,137, 1900)

A hand drill you work by pushing a handle back and forth. The handle's nut runs on a spiral-grooved rod and spins it one way, then the other. Inside a bulb-shaped casing you hold in your other hand, bevel gears and two sliding ratchet bolts turn that back-and-forth spin into steady rotation of the chuck, so the bit cuts on every stroke. Result: a hand drill that bores continuously in one direction from a push-pull stroke. Source: J. E. Olson, US 652,137 (1900). Unknown: all materials and sizes. Picture: the patent drawing.
Avançado
Unknown

Instruções

1

Make the casing

Make two half-egg-shaped shells, each with a half-round neck at both ends. Put them face to face and hold them together with ferrules pushed over the necks: a hollow bulb that fits the hand. Not given: the metal, sizes.

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 shells, ferrules

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Dimensões desconhecidasDimensões desconhecidas
2

Make the spiral rod and handle

Cut a rod with a steep spiral groove or thread. Fit a tube over it with a nut at its lower end that runs in the spiral, and a handle at its upper end. Not given: the pitch, the handle material.

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 rod, tube, nut
Material desconhecidoMaterial desconhecido1 handle

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Jogo de machos e cossinetesJogo de machos e cossinetes
3

Make the gears and ratchet hub

Take four bevel wheels: an upper one bored through the centre and fixed on the lower end of the spiral rod, a lower one the same shape and size, and two side wheels that gear them together. Cut a ring of ratchet teeth on the facing sides of the upper and lower wheels, slanted opposite ways. Make a shaft with a hub (barrel) at its top whose tip runs in the bore of the upper wheel; cut two upright dovetail grooves in the hub, each holding a sliding bolt with its two ends bevelled opposite ways, long enough that one end meets one wheel's teeth while the other end is clear of the other wheel. Ours: steel mitre gears.

Materiais para este passo:

Conjunto de engrenagens cónicas (aço, 1:1)Conjunto de engrenagens cónicas (aço, 1:1)2 four bevel wheels
Metal desconhecidoMetal desconhecido1 shaft, hub, two bolts

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Serra de arco para metaisSerra de arco para metais
4

Assemble

Inside the casing, set the upper wheel with the spiral rod coming out of the top neck, the hub between the wheels, and the lower wheel turning loose on the shaft. Run the two side wheels on screws through the casing wall as their axles. Bring the shaft out of the lower neck and fix a drill chuck on its end. Ours: a drill chuck.

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 two journal screws
Bucha de berbequimBucha de berbequim1 peça

Ferramentas necessárias:

Jogo de machos e cossinetesJogo de machos e cossinetes
5

Drill

Put a bit in the chuck and set it on the mark. Hold the casing still in one hand, pressing lightly toward the work, and push and pull the handle with the other. Each stroke turns the upper and lower wheels opposite ways; the bolts slide over to engage whichever wheel is turning the cutting way, so the bit turns steadily one way.

Ferramentas necessárias:

Jogo de brocasJogo de brocas

Materiais

4

Ferramentas necessárias

5

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...