Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Hand-Sewn Welted Boot: Last, Welt, Sole, Heel and Finish (Hasluck, Boot Making and Mending, 1898)
Tex

Criado por

Tex

13. novembro 2026FO
9
0
0
0
0

Hand-Sewn Welted Boot: Last, Welt, Sole, Heel and Finish (Hasluck, Boot Making and Mending, 1898)

How a closed boot upper becomes a hand-sewn welted boot, from Paul N. Hasluck's Boot Making and Mending (1898): measure the foot and fit up the last, block and feather the insole, last the upper tight, sew in the welt and the seat, fill and lay the sole, round it, channel and stitch it to the welt, build and sew the heel, then knife, iron, ink and heel-ball the edges. All sizes are his. The upper here is the Wellington leg from Leno's book (the previous blueprint).
Avançado
About 1 week

Instruções

1

Sizes, lasts and heel

A carregar o notebook Jupyter…
2

Read Boot Making and Mending, ch. IV

"In choosing the materials, it should be remembered that a boot, like a house, depends upon the foundation, for which reason the leather should be good of its class, and every care exercised to fit it properly."
3

Measure the foot

Have the person stand full weight on a sheet of paper and draw round the foot with the pencil quite upright, then the lines of the waist. Take the length on the drawing. With a tape take, in inches and only just tight: the joint (under the foot, over the great-toe joint and little-toe knuckle), the second joint round the ball, the instep, the heel measure (round the heel, under the ankle bone, across the throat) and the leg about 1½ in above the ankle bone. Mark each on the drawing.

Materiais para este passo:

Folha quadrada de papelFolha quadrada de papel1 peça

Ferramentas necessárias:

LápisLápis
Fita métricaFita métrica
Medidor de númerosMedidor de números
4

Fit up the last

Choose a last whose toe is nearest the shape wanted; set it on the drawing and check the lines and girths. Rasp off any surplus so the bottom is shaped as his Fig. 69, leaving room for the great toe. If it is too small, make fittings from wetted, stretched flank leather (long leather, joint, toe-pin, heel-pin), skive them thin to the edge, tack them on wet and let each dry before blocking and trimming. Peg bunion pieces with fine ½ in pegs in holes made with the peg awl. An old shoe worn to the foot is "the safest guide": put the last in it to see where it is short.

Materiais para este passo:

Couro para arreiosCouro para arreios1 peça
Cavilhas de madeiraCavilhas de madeira1 peça
Tachas de montarTachas de montar1 peça

Ferramentas necessárias:

Forma de sapateiroForma de sapateiro
GrosaGrosa
Faca de chanfrar couroFaca de chanfrar couro
Sovela de cavilhasSovela de cavilhas
Martelo de unhaMartelo de unha
5

Prepare the stuff

Soak insoles, outer soles, stiffeners, lifts and top-pieces in clean water. Mark the welts down the centre with compasses, cut them to equal widths and put them in the water too; they are used wet. Dry the rest in a draught, not near a fire. When the soles are just mellow, buff off the grain lightly and skive the flesh off the back; do the same to lifts and top-pieces. Hammer them evenly all over on the lap iron, grain down, from the centre; the lifts less hard than soles and top-pieces.

Materiais para este passo:

Sola de couroSola de couro1 peça
Vira de couroVira de couro1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Compasso de pontasCompasso de pontas
Faca para couroFaca para couro
Raspador de sapateiroRaspador de sapateiro
Ferro de coloFerro de colo
Martelo de unhaMartelo de unha
6

Block, feather and hole the insole

Mark the insole to the last, cut it out, buff the grain and tack it grain down with four tacks in the middle; stretch the sides with pincers and tack it tight till nearly dry (blocking). Round it to the last, narrower in the waist. Rub with soap, draw a margin ¼ to ⅓ in from the edge with compasses, wider at the waist, cut it about one-third through with the knife upright, open it with the prick-stitch and cut away the strip to leave the feather. Gauge a second line the same distance in and pass the sewing awl from it to the edge of the feather. Take the sharp edge off the grain side.

Materiais para este passo:

Sola de couroSola de couro1 peça
Tachas de montarTachas de montar1 peça
Sabonete em barraSabonete em barra1 peça

Ferramentas necessárias:

Forma de sapateiroForma de sapateiro
Faca para couroFaca para couro
Torquês de montarTorquês de montar
Compasso de pontasCompasso de pontas
Marcador de pontosMarcador de pontos
Sovela de coserSovela de coser
7

Stiffeners and side linings

Cut the stiffeners from good leather, used wet; a gentleman's 1¾ in high at the back. Skive them all round on both sides, little on the grain side, the top to a feather edge, the bottom to half its substance. Cut side linings, best of oil-dressed calf.

Materiais para este passo:

Sola de couroSola de couro1 peça
Couro de vitelaCouro de vitela1 peça

Ferramentas necessárias:

Faca de chanfrar couroFaca de chanfrar couro
8

Last the upper

Paste the stiffener on both sides and put it between lining and leather at the back seam. With the last on your knees, pull the upper down at the toe and set the back seam on the centre of the last, covering about two-thirds of it at the back ("horsing"). Draw the toe tight with the pincers and tack at A, then B and B, then the draft tacks C and C, pulling hard to put a draft in. Put the side linings in unpasted and tack D and D, lasting the lining tight. Last the sides till all fulness is gone, knock the heel of the last in, and last waist and seat, less hard. Last the toe last, drawing stuff to the toe and tapping out every pipe and wrinkle with the hammer; never cut V-pieces out of the pipes.

Materiais para este passo:

Gáspea de botaGáspea de bota1 peça
Cola de farinha de trigoCola de farinha de trigo1 peça
Tachas de montarTachas de montar1 peça

Ferramentas necessárias:

Forma de sapateiroForma de sapateiro
Torquês de montarTorquês de montar
Martelo de unhaMartelo de unha
Sovela de coserSovela de coser
9

Prepare the welts

Take a fine shaving off the grain side of the wet welts and, if needed, reduce them from the flesh side. Cut an angular piece about ³⁄₁₆ in wide, about two-thirds through, along one corner of the grain side, by pulling the welt past a knife dug into the cutting-board. Choose the width from the notebook.

Materiais para este passo:

Vira de couroVira de couro1 peça

Ferramentas necessárias:

Faca para couroFaca para couro
Tábua de pinhoTábua de pinho
10

Make the threads and sew in the welt

Make waxed threads of hemp with cobbler's wax and a bristle at each end, nicely twisted and smooth. Damp the boot over the holes. Starting at the left corner of the seat, toe toward you, held with a strap under your foot over the waist, skive the welt to half its substance for the waist length. Pass the sewing awl through the insole hole and the welt, put both bristles through from opposite sides, pull the stitch through in quick strokes and set it with a hard tightening pull, the thread round the hand leather and the awl handle. Hammer the seam every five or six stitches; wax the ends as you go. Draw each lasting tack as you reach it. Skive the welt again at the other joint, sew to F and cut it off under the last stitch. Trim the surplus upper close to the stitch and hammer the seam down.

Materiais para este passo:

Vira de couroVira de couro1 peça
Fibra de cânhamoFibra de cânhamo1 peça
Cera de sapateiroCera de sapateiro1 peça
Cerdas de javaliCerdas de javali1 peça

Ferramentas necessárias:

Sovela de coserSovela de coser
Manopla de sapateiroManopla de sapateiro
Correia de couroCorreia de couro
Martelo de unhaMartelo de unha
Faca para couroFaca para couro
11

Sew the seat

Wax the ends well; use one thread long enough to go right round. Sew the heel seat the same way but with no welt, the stitch lying on the insole one side and on the upper the other. Make very solid stitches, pull the last end through to the insole and tie the two ends in a good knot. Take out the four tacks.

Materiais para este passo:

Fibra de cânhamoFibra de cânhamo1 peça
Cera de sapateiroCera de sapateiro1 peça
Cerdas de javaliCerdas de javali1 peça

Ferramentas necessárias:

Sovela de coserSovela de coser
Manopla de sapateiroManopla de sapateiro
12

Fill the bottom

Rub chalk on the stitches and tap a piece of felt on the insole to mark its size; paste the insole, lay the felt on, hammer it and trim it level with the welt when dry. Peg a piece of good solid leather in the waist with about four pegs, skived thin at the ends and sides, paste it and cover it with thin split felt; add another layer if the bottom is hollow, until it is level with the welt. Rub in powdered French chalk.

Materiais para este passo:

Feltro de lãFeltro de lã1 peça
Cola de farinha de trigoCola de farinha de trigo1 peça
Couro para arreiosCouro para arreios1 peça
Cavilhas de madeiraCavilhas de madeira1 peça
Giz francês (talco)Giz francês (talco)1 peça

Ferramentas necessárias:

Sovela de cavilhasSovela de cavilhas
Martelo de unhaMartelo de unha
Faca para couroFaca para couro
13

Lay the sole

Wet the sole leather, dry it till just mellow, scrape the grain, flesh the back and hammer it from the centre out. Mark it round to the boot and cut off the spare toe piece. Paste the sole's flesh side and the bottom of the boot, chalk the felt, and fix the sole with sole tacks at the toe, at B and two at C. Tap it all over; for an ordinary waist skive the sole's flesh side at the waist, leaving it thicker next the welt; for riding boots it may be left full (a square waist). Run a blunt bone round between upper and welt to set the welt flat.

Materiais para este passo:

Sola de couroSola de couro1 peça
Cola de farinha de trigoCola de farinha de trigo1 peça
Giz francês (talco)Giz francês (talco)1 peça
Tachas de montarTachas de montar1 peça

Ferramentas necessárias:

Faca para couroFaca para couro
Martelo de unhaMartelo de unha
Ferro de coloFerro de colo
Dobradeira de ossoDobradeira de osso
14

Round up and channel the sole

Hold the boot on its side on the knees and pare the sole round to shape with a very sharp knife, the point overhanging the guiding finger only by the sole's thickness, little by little, closer at the toe and wider toward the waist, leaving stuff at the seat; keep the edge even and square. Mark the channel about ¹⁄₁₆ in from the edge in the fore part and about ¼ in in the waist; cut it with the knife at about 50 degrees to the welt, nearly half-way through, and open it with the prick-stitch, throwing the grain back.

Ferramentas necessárias:

Faca para couroFaca para couro
Compasso de pontasCompasso de pontas
Marcador de pontosMarcador de pontos
15

Stitch the sole

Make the stitching thread of yellow flax waxed with white wax or beeswax, twisted lighter and wiry. Run the fudge wheel round the welt to mark the stitches. With the strap over the waist, thrust the stitching awl through welt and sole into the channel in one quick, straight jerk, never wriggled, and set each stitch the same way. Rub the stitches down with the bone, paste the channel thinly and lay it down with the smooth side of an old file, trim the burr level, damp the sole and rub it down with the long-stick; hammer it all over.

Materiais para este passo:

Fio de linhoFio de linho1 peça
Cera de abelhaCera de abelha1 peça
Cerdas de javaliCerdas de javali1 peça
Cola de farinha de trigoCola de farinha de trigo1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Roda de marcar viraRoda de marcar vira
Sovela de pespontarSovela de pespontar
Correia de couroCorreia de couro
Dobradeira de ossoDobradeira de osso
Jogo de limasJogo de limas
Faca para couroFaca para couro
Brunidor de costurasBrunidor de costuras
Martelo de unhaMartelo de unha
16

Fit the seat-piece

Cut the seat-piece straight on one edge, file it, paste both pieces, butt the edges, nail at A and peg about five pegs in the seat-piece and two in the sole, about ½ in from the edge. Pare it to shape, overhanging the stitches ¼ in, and take the angle off round for a third or bare half of the thickness. Draw the nail, cut off the peg tops, cut the grain away round them and rasp the top rough.

Materiais para este passo:

Sola de couroSola de couro1 peça
Cola de farinha de trigoCola de farinha de trigo1 peça
Cavilhas de madeiraCavilhas de madeira1 peça

Ferramentas necessárias:

Jogo de limasJogo de limas
Sovela de cavilhasSovela de cavilhas
Martelo de unhaMartelo de unha
Faca para couroFaca para couro
GrosaGrosa
17

Make the split-lift and first lifts

Cut a piece of first-cut butt leather about 7 in x 1 in and, wet, split it on the slant into two wedge-shaped strips; bend each round on the lap iron and hammer the puckers flat. Rasp and paste the seat and the split-lift, lay it flush at the back of the seat and peg it, the pegs toward the centre; pare it round. Rough and paste the first whole lift, peg it on with about five pegs, rasp it and trim it; lay the second lift with two ¾ in rivets.

Materiais para este passo:

Sola de couroSola de couro1 peça
Cola de farinha de trigoCola de farinha de trigo1 peça
Cavilhas de madeiraCavilhas de madeira1 peça
Rebites de sapateiroRebites de sapateiro1 peça

Ferramentas necessárias:

Faca para couroFaca para couro
Ferro de coloFerro de colo
GrosaGrosa
Sovela de cavilhasSovela de cavilhas
Martelo de unhaMartelo de unha
18

Sew down the heel

Cut a V-groove channel in the top lift. Rub the seat with the bone. With a thread four to six strands stouter than sewing thread and the heel awl dipped in soap, sew the heel down from corner to corner, each stitch passing through the loop of the seat stitch, hammering every few stitches, and knot the last. Pene the heel all round with the pene of the hammer to drive the leather over the stitches, trim the seat with the knife and a metal guard, sweep the seat-breaker round, and smooth the edge with a welt file.

Materiais para este passo:

Fibra de cânhamoFibra de cânhamo1 peça
Cera de sapateiroCera de sapateiro1 peça
Cerdas de javaliCerdas de javali1 peça
Sabonete em barraSabonete em barra1 peça

Ferramentas necessárias:

Sovela de saltoSovela de salto
Manopla de sapateiroManopla de sapateiro
Martelo de unhaMartelo de unha
Dobradeira de ossoDobradeira de osso
Faca para couroFaca para couro
Aparador de assentoAparador de assento
Jogo de limasJogo de limas
19

Finish the heel

For a 1¼ in heel add two more lifts and the top piece: rough and paste each, rivet the third lift nearly in the centre, then the last lift, and hold the top piece with headless rivets so it can be rounded. Round it up, longer and squarer on the outside corner; put the remaining rivets in, slanting outward, not near the edge. Check with a straight-edge that the top piece is level with the flat of the sole.

Materiais para este passo:

Sola de couroSola de couro1 peça
Cola de farinha de trigoCola de farinha de trigo1 peça
Rebites de sapateiroRebites de sapateiro1 peça

Ferramentas necessárias:

GrosaGrosa
Martelo de unhaMartelo de unha
Faca para couroFaca para couro
20

Knife up, rasp and buff

Round the top piece, then pare the heel all round with the knife, dropping the hand and raising the knife, going round again and again until no bumps can be felt; a piece of horn or bone between upper and seat guards the upper. Knife up the sole edge, rasp it, damp it and scrape it with the buffing knife, keeping it hollow, and sandpaper.

Materiais para este passo:

LixaLixa1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Faca para couroFaca para couro
GrosaGrosa
Raspador de sapateiroRaspador de sapateiro
Pedra de amolarPedra de amolar
21

Iron, ink and heel-ball

Warm the irons over a spirit lamp, only just warm, wiping each on a rag. Damp the edges and run the forepart, welt, waist and top-piece irons and the seat wheel round, holding each upright and firm. Rub weak ammonia-and-water on the parts to be blacked, then ink them with shoemaker's ink diluted with an equal part of water; when just dry, iron again. Melt heel-ball over the lamp, dab it on the ironed parts and iron it in with the irons a degree cooler, then rub it off with a cloth to a smooth, even gloss. Fudge or prick up the welt.

Materiais para este passo:

Tinta para couroTinta para couro1 peça
Solução de amoníaco diluídaSolução de amoníaco diluída1 peça
Cera de saltos (heel ball)Cera de saltos (heel ball)1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Lamparina de álcoolLamparina de álcool
Ferro de bordasFerro de bordas
Roda de assentoRoda de assento
Roda de marcar viraRoda de marcar vira
22

Take out the last and finish inside

Take out the block screw, hook the last hook into its hole over the heel, put your feet on the handle and pull the boot off. Paste a seat-sock on its wrong side to within ⅛ in of the edge and put it in. Tap the insole feather down lightly on either side with a smooth-headed hammer. A thin coat of weak paste and a first blacking, sleeked with bone while on the last, save trouble in cleaning calf.

Materiais para este passo:

Couro de vitelaCouro de vitela1 peça
Cola de farinha de trigoCola de farinha de trigo1 peça

Ferramentas necessárias:

Gancho de formaGancho de forma
Martelo de unhaMartelo de unha
Dobradeira de ossoDobradeira de osso
23

Troubleshooting

Welted boot troubleshooting.

Flow

Loading...
24

History and honest limits

From **Boot Making and Mending**, edited by Paul N. Hasluck, Cassell and Company, London, 1898 (Project Gutenberg #78854), chapters IV-VIII. His lasting chapter describes a laced boot; here the upper is the Wellington leg of the previous blueprint. Not made here: the pegged seat and waist, the flexura steel waist spring, riveted work, and the black, buff and white bottom finishes beyond the edges. All sizes are his; the metric figures are ours.

Materiais

23

Ferramentas necessárias

30

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...