Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Honey Extractor: a Tinplate Cylinder Extractor (Hasluck, 1905)
Forge

Criado por

Forge

4. novembro 2026NO
16
0
0
1
0

Honey Extractor: a Tinplate Cylinder Extractor (Hasluck, 1905)

A two-comb honey extractor built by a tinsmith: a soldered tinplate frame carrying two wire-netting comb baskets on a 1/2 in spindle, spun by bought gearing inside a tinplate cylinder with a sloping bottom that drains through a treacle valve. Only the frame and combs revolve, not the can and the honey already thrown out, so it starts and stops easily; a comb that turns lighter tells you its side is empty. Source: P. N. Hasluck, Beehives and Bee Keepers' Appliances (1905), pp. 122-132. Picture: the book's Figs. 115-116.
Avançado
Unknown

Instruções

1

Make the two bands

Take three sheets of tinplate 17 in by 12 1/2 in and cut one into six strips 2 in wide; pare the edges straight. Join three strips end to end by turning 1/4 in over at the ends, hooking them together, hammering flat and touching with solder; do the same with the other three. Cut each to 45 in and wire both edges with wire about 1/8 in diameter (about No. 10 gauge), 44 in long: turn the edge over nearly 1/2 in with mallet and stake, lay the wire in, and hammer the tin down round it. Use fine solder with a large proportion of tin throughout. Bend each strip in a wooden vice into a rectangular band 12 in by 10 in, square at the corners and not in winding, wired edge outwards; solder the overlapping inch.

Materiais para este passo:

Chapa de folha de flandresChapa de folha de flandres3 17 x 12 1/2 in sheets
Arame de ferroArame de ferro1 about 1/8 in, No. 10
Solda de estanho-chumboSolda de estanho-chumbo1 peça

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Maço de madeiraMaço de madeira
EstacaEstaca
Ferro de soldarFerro de soldar
Torno de bancadaTorno de bancada
2

Fit the bridges

From another sheet cut two pieces 12 in by 3 1/2 in. Wire both edges with wires only 10 in long placed in the middle, leaving 1 in free at each end, and hammer the turned edges flat at the ends. Turn the unwired ends up sharp to make a tin stool 10 in long with legs 1 in high. Fasten one across each band the narrow way, equidistant from the short sides, with solder and small rivets. The bridges carry the spindle.

Materiais para este passo:

Chapa de folha de flandresChapa de folha de flandres1 peça
Arame de ferroArame de ferro1 peça
Rebites de ferroRebites de ferro1 peça
Solda de estanho-chumboSolda de estanho-chumbo1 peça

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Maço de madeiraMaço de madeira
EstacaEstaca
Ferro de soldarFerro de soldar
MarteloMartelo
3

Make the four slides

Cut four pieces of tinplate 16 1/2 in by 3 1/8 in and cut small rectangles out of the corners. Turn over and hammer down 1/4 in at each long edge and 1/2 in at one short end. Turn the long edges up at right angles and the short end too, making a trough open at one end with the other end twice as high as the sides. Touch the corners with solder, nip off the sharp corners of the projecting end and round them with a file.

Materiais para este passo:

Chapa de folha de flandresChapa de folha de flandres1 peça
Solda de estanho-chumboSolda de estanho-chumbo1 peça

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Maço de madeiraMaço de madeira
EstacaEstaca
Ferro de soldarFerro de soldar
Lima para metalLima para metal
4

Assemble the frame

Lay one band on the bench, bridge up. Stand a slide, stopped end down, in a corner with its back against a long side of the band, hold the two with a small cramp and two pieces of wood, check with the square, and run solder between them; do the other three. Put the upper band over the tops of the slides; if a slide is out of true, unsolder and reset it. Both bridges must face upwards so they do not hold honey.

Materiais para este passo:

Solda de estanho-chumboSolda de estanho-chumbo1 peça

Ferramentas necessárias:

Grampo em CGrampo em C
Esquadro fixoEsquadro fixo
Ferro de soldarFerro de soldar
5

Make the comb baskets

Cut four pieces of wire netting, two 15 in by 9 5/8 in and two 1/4 in narrower. Bind each round with tinplate strips 3/4 in wide overlapping 3/8 in each side, soldering every wire to the tin, then turning the tin over and soldering every wire again. Solder up four strips 41 in by 2 1/4 in, turn the edges over 1/4 in and turn one edge up square, so the section is an L with legs 1 1/2 in and 1/4 in. Cut the narrow rib with a chisel at the bends and bend each strip into the three sides of a half-basket, the short side 9 3/4 in on two and 1/8 in less on the other two. Solder the framed netting against the rib. On the wider pair turn over the 5/8 in that projects with a short wire in it as a pull; on the narrower pair clip some off and turn 1/4 in down. Cut a hole in the end of each half for the frame's top bar. Solder two crossing wires 1/8 in thick over the netting, joined in the middle and bent flat, to stop it bulging.

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 wire netting, metal not given (never zinc)
Chapa de folha de flandresChapa de folha de flandres1 peça
Arame de ferroArame de ferro1 1/8 in
Solda de estanho-chumboSolda de estanho-chumbo1 peça

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Maço de madeiraMaço de madeira
EstacaEstaca
Ferro de soldarFerro de soldar
TalhadeiraTalhadeira
6

Make the cylinder

Take a tinplate 55 in by 26 in, wire the top and bottom edges with 1/4 in wire, bend it into a cylinder and solder the joint. Cut a bottom about 1/2 in larger than the cylinder's diameter, turn its edge up 1/4 in, set it in sloping, turn the flange down and solder it firmly to the sides. Fit the treacle valve at the lowest point. Solder a bearing for the spindle at the centre of the bottom, its underside filed to the slope so its top is level. Rivet two bands of hoop iron 1/8 in thick and 1 1/4 in wide under the beads.

Materiais para este passo:

Chapa de folha de flandresChapa de folha de flandres1 55 x 26 in
Arame de ferroArame de ferro1 1/4 in
Torneira de melTorneira de mel1 peça
Barra chata de aço macioBarra chata de aço macio1 hoop iron 1/8 x 1 1/4 in
Rebites de ferroRebites de ferro1 peça
Solda de estanho-chumboSolda de estanho-chumbo1 peça

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Maço de madeiraMaço de madeira
EstacaEstaca
Ferro de soldarFerro de soldar
Lima para metalLima para metal
Berbequim de mãoBerbequim de mão
MarteloMartelo
7

Fit the spindle

Make the spindle once the can is finished and its length is known: 1/2 in round iron or steel, tinned all over, with the lower end brought to a long cone to run in the bottom bearing. Pass it through the middle of both bridges so the cages run true, with the tops of the cages 2 in below the top of the can, and solder it to the bridges. Strengthen the hold with tin washers 1 1/2 in diameter, beaten saucer-shaped, with holes made a little small and turned out until the spindle passes; solder them to spindle and bridges.

Materiais para este passo:

Barra redonda de aço macioBarra redonda de aço macio1 1/2 in round
Chapa de folha de flandresChapa de folha de flandres1 peça
Solda de estanho-chumboSolda de estanho-chumbo1 peça

Ferramentas necessárias:

Lima para metalLima para metal
Ferro de soldarFerro de soldar
Tesoura de chapaTesoura de chapa
MarteloMartelo
8

Fit the cross-bar, gearing and covers

Attach bolts to the top hoop, one of them breaking the joint of the hoop, to hold a cross-bar 1 1/4 in wide, long enough to reach across, drilled for the bolts and the spindle; make it 1/2 in thick when gearing is used, and fasten it with fly nuts or hexagon nuts. Key the pinion to the spindle and run the toothed wheel on a stud riveted to the cross-bar. Rivet a pair of handles to the sides, and make two flat covers, one each side of the cross-bar, with edges turned down to embrace the rim, like a saucepan cover.

Materiais para este passo:

Barra chata de aço macioBarra chata de aço macio1 cross-bar 1 1/4 x 1/2 in
Sortido de parafusos sextavadosSortido de parafusos sextavados1 peça
Porca borboletaPorca borboleta1 peça
PinhãoPinhão1 peça
Roda dentada movidaRoda dentada movida1 peça
Rebites de ferroRebites de ferro1 peça
Chapa de folha de flandresChapa de folha de flandres1 peça

Ferramentas necessárias:

Berbequim de mãoBerbequim de mão
MarteloMartelo
Tesoura de chapaTesoura de chapa
Maço de madeiraMaço de madeira

Materiais

12

Ferramentas necessárias

11

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...